Intec CS4000 - [Admin Setup]

- 250 - - 251 -
Table of setting items in the device setup screen Table of setting items in the device setup screen
1
2
3
5
4
1
2
3
5
4
Convenient print
functions
Appendix Index
Checking and
Changing Printer
Settings Using
the Control Panel
Network
Setup
Matching
Colors
Using Utility
Software
Convenient print
functions
Appendix Index
Checking and
Changing Printer
Settings Using
the Control Panel
Network
Setup
Matching
Colors
Using Utility
Software
z
Shaded areas are factory-set values.
Item Details
Hub Link Setting Auto
100Base-TX
Full
100Base-TX
Half
10Base-T Full
10Base-T Half
Sets the connection mode to the hub.
Network Factory Defaults Execute Restores the settings such as network, mail
server, LDAP server, and secure protocol
server, etc., to their default values.

USB Setup
z
Shaded areas are factory-set values.
Item Details
USB Enable
Disable
Enables/disables access using a USB interface.
Speed
480Mbps
12Mbps
Sets the maximum baud rate using a USB interface.
Soft Reset
Enable
Disable
Enables/disables the software reset command.
Serial Number
Enable
Disable
Enables/disables the USB serial number.
The USB serial number is used to identify USB
devices connected to a PC.
Ofine Receive
Enable
Disable
Sets whether to receive data even if ofine or a
recoverable error occurs.
[Admin Setup]
Note
z
To enter this menu, it is necessary to enter the [Password].
z
In the default factory settings, the administrator password is [aaaaaa].

Network Setup
z
Shaded areas are factory-set values.
Item Details
TCP/IP Enable
Disable
Enables/disables the TCP/IP protocols.
NetBIOS over TCP
*
*: Displayed if [TCP/IP] in the control panel is set to
[Enable].
Enable
Disable
Enables/disables the NetBIOS over TCP/IP.
EtherTalk
Enable
Disable
Enables/disables EtherTalk.
IP Address Set
*
*: Displayed if [TCP/IP] in the control panel is set to
[Enable].
Auto
Manual
Sets whether to request the IP address from
the DHCP server.
IPv4 Address
*
*: Displayed if [TCP/IP] in the control panel is set to
[Enable].
xxx.xxx.xxx.
xxx
Sets the IP address.
Subnet Mask
*
*: Displayed if [TCP/IP] in the control panel is set to
[Enable].
xxx.xxx.xxx.
xxx
Sets the subnet mask.
Gateway Address
*
*: Displayed if [TCP/IP] in the control panel is set to
[Enable].
xxx.xxx.xxx.
xxx
Sets the gateway address.
Web
*
*: Displayed if [TCP/IP] in the control panel is set to
[Enable].
Enable
Disable
Enables/disables access using web browsers.
Telnet
*
*: Displayed if [TCP/IP] in the control panel is set to
[Enable].
Enable
Disable
Enables/disables access using TELNET.
FTP
*
*: Displayed if [TCP/IP] in the control panel is set to
[Enable].
Enable
Disable
Enables/disables access using FTP.
IPSec
*
*: Displayed if [TCP/IP] in the control panel is set to
[Enable].
Enable
Disable
Enables/disables access using IPSec.
SNMP
*
*: Displayed if [TCP/IP] in the control panel is set to
[Enable].
Enable
Disable
Enables/disables access using SNMP.
Network Scale
Normal
Small
Normal:
The printer will operate effectively even
if connected to a hub with spanning tree
functions. Small scale, however, is 2 to 3
PCs.
When connected to a small-scale LAN, the
printer startup time will be lengthened.
Small:
From small scale LANs with 2 or 3 PCs
to large scale LANs are covered, but if
connected to a hub with spanning tree
functions, operations may not be effective.
Gigabit Network
Enable
Disable
Sets whether to support a Gigabit network.