Keysight DSOX1202A - Remote Front Panel; Remote Programming Via the Web Interface

To Next Page

To Previous Page

252 Keysight InfiniiVision 1200 X-Series and EDUX1052A/G Oscilloscopes User's Guide

23 Web Interface

Remote Front Panel

To operate the oscilloscope using the web interface's browser-based Remote

Front Panel:

1 Access the oscilloscope's web interface (see "Accessing the Web Interface" on

page 250).

2 When the oscilloscope's web interface is displayed, select Control Instrument,

then select UseRemoteFrontPanel. After a few seconds the Remote Front Panel

appears.

3 Click keys or knobs that you would normally press on the oscilloscope's front

panel. Buttons have been added for turning knobs.

Remote Programming via the Web Interface

NOTE

If Java is not installed on your PC, you will be prompted to install the Java Plug-in. This

plug-in must be installed on the controlling PC for the web interface's Remote Programming

operations.

Main Page

Default Chapter3
- Infiniivision 1200 X-Series and EDUX1052A/G Oscilloscopes-At a Glance3
- In this Guide6
- Table of Contents9
1 Getting Started21
- Inspect the Package Contents21
- Power-On the Oscilloscope22
- Connect Probes to the Oscilloscope23
  - Maximum Input Voltage at Analog Inputs23
  - Do Not Float the Oscilloscope Chassis23
- Input a Waveform23
- Recall the Default Oscilloscope Setup24
- Use Autoscale24
- Compensate Passive Probes25
- Learn the Front Panel Controls and Connectors26
  - Front Panel Overlays for Different Languages33
- Learn the Rear Panel Connectors33
- Learn the Oscilloscope Display34
- Access the Built-In Quick Help36
- Select the User Interface Language36
2 Horizontal Controls38
- To Adjust the Horizontal (Time/DIV) Scale38
- To Adjust the Horizontal Delay (Position)39
- Panning and Zooming Single or Stopped Acquisitions40
- To Change the Horizontal Time Mode (Normal, XY, or Roll)40
  - XY Time Mode41
- To Display the Zoomed Time Base44
- To Change the Horizontal Scale Knob's Coarse/Fine Adjustment Setting45
- To Position the Time Reference (Left, Center, Right)46
3 Vertical Controls48
- To Turn Waveforms on or off (Channel or Math)49
- To Adjust the Vertical Scale49
- To Adjust the Vertical Position49
  - Vertical Controls49
- To Specify Channel Coupling50
- To Specify Bandwidth Limiting50
- To Change the Vertical Scale Knob's Coarse/Fine Adjustment Setting51
- To Invert a Waveform51
- Setting Analog Channel Probe Options51
4 Analog Bus Display57
5 FFT Spectral Analysis57
- FFT Measurement Hints60
- FFT Units61
- FFT DC Value61
- FFT Aliasing62
- FFT Spectral Leakage63
6 Math Waveforms66
- To Display Math Waveforms66
- To Perform a Math Function on an Arithmetic Operation67
- To Adjust the Math Waveform Scale and Offset67
- Units for Math Waveforms67
- Math Operators68
  - Add or Subtract68
  - Multiply or Divide69
- Math Transforms70
  - FFT Magnitude, FFT Phase70
- Math Filters74
  - Low Pass Filter74
7 Reference Waveforms77
- To Save a Waveform to a Reference Waveform Location77
- To Display a Reference Waveform78
- To Scale and Position Reference Waveforms79
- To Adjust Reference Waveform Skew79
- To Display Reference Waveform Information80
- To Save/Recall Reference Waveform Files To/From a USB Storage Device80
- 8 Serial Bus Decode/Trigger81
- 9 Display Settings83
10 Labels91
- To Turn the Label Display on or off91
- To Assign a Predefined Label to a Channel92
- To Define a New Label93
- To Load a List of Labels from a Text File You Create94
- To Reset the Label Library to the Factory Default95
11 Triggers97
- Adjusting the Trigger Level99
- Edge Trigger99
- Forcing a Trigger99
- Pulse Width Trigger102
- Pattern Trigger104
- Rise/Fall Time Trigger106
- Setup and Hold Trigger107
- Video Trigger108
- Serial Trigger118
- To Select the Auto or Normal Trigger Mode122
12 Trigger Mode/Coupling122
- To Select the Trigger Coupling124
- To Enable or Disable Trigger HF Reject125
- To Enable or Disable Trigger Noise Rejection125
- To Set the Trigger Holdoff126
- External Trigger Input127
13 Acquisition Control129
- Running, Stopping, and Making Single Acquisitions (Run Control)129
- Overview of Sampling130
- Selecting the Acquisition Mode135
- Acquiring to Segmented Memory141
- To Make Cursor Measurements146
- Cursor Examples150
- To Make Automatic Measurements156
- Measurements Summary157
  - Snapshot All159
- Voltage Measurements160
- Time Measurements167
- Count Measurements174
- Measurement Thresholds175
- Measurement Window with Zoom Display177
16 Mask Testing179
- To Create a Mask from a "Golden" Waveform (Automask)179
- Mask Test Setup Options182
- Mask Statistics184
- To Manually Modify a Mask File185
- Building a Mask File188
  - How Is Mask Testing Done191
17 Digital Voltmeter193
18 Frequency Response Analysis197
- To Make Connections197
- To Set up and Run the Analysis198
- To View and Save the Analysis Results200
19 Waveform Generator203
- To Select Generated Waveform Types and Settings203
- To Specify the Expected Output Load206
- To Add Noise to the Waveform Generator Output207
- To Use Waveform Generator Logic Presets207
- To Add Modulation to the Waveform Generator Output208
- To Restore Waveform Generator Defaults213
20 Save/Recall (Setups, Screens, Data)215
- Saving Setups, Screen Images, or Data215
- Recalling Setups, Masks, or Reference Waveforms222
- Performing a Secure Erase224
- Recalling Default Setups224
21 Print (Screens)227
- To Print the Oscilloscope's Display227
- To Set up Network Printer Connections229
- To Specify the Palette Option230
- To Specify the Print Options230
- I/O Interface Settings231
- Setting up the Oscilloscope's LAN Connection232
  - To Establish a LAN Connection233
  - Stand-Alone (Point-To-Point) Connection to a PC234
22 Utility Settings232
- File Explorer234
- Setting Oscilloscope Preferences236
- Setting the Gen out Source240
- Setting the Oscilloscope's Clock240
- Enabling Remote Command Logging241
- Performing Service Tasks243
- Configuring the [Quick Action] Key246
  - Utility Settings247
- Accessing the Web Interface250
23 Web Interface250
- Control Instrument251
- Get Image254
- Save/Recall255
  - Saving Files Via the Web Interface255
  - Recalling Files Via the Web Interface256
- Identification Function257
- Instrument Utilities258
- Setting a Password259
24 Reference261
- Measurement Category261
- Specifications and Characteristics261
- Environmental Conditions263
  - Declaration of Conformity263
- Probes and Accessories263
- Binary Data (.Bin) Format264
- Software and Firmware Updates264
- CSV and ASCII XY Files271
  - CSV and ASCII XY File Structure272
  - Minimum and Maximum Values in CSV Files272
- Acknowledgements273
- Product Markings and Regulatory Information273
25 CAN Triggering and Serial Decode275
- Setup for CAN Signals275
- CAN Triggering277
- CAN Serial Decode279
26 I2C Triggering and Serial Decode285
- Setup for I2C Signals285
- I2C Triggering286
- I2C Serial Decode290
  - Interpreting I2C Decode291
  - Interpreting I2C Lister Data292
27 LIN Triggering and Serial Decode293
- Setup for LIN Signals293
- LIN Triggering295
- LIN Serial Decode297
  - Interpreting LIN Decode299
  - Interpreting LIN Lister Data300
- Setup for SPI Signals301
28 SPI Triggering and Serial Decode301
- SPI Triggering307
- SPI Serial Decode309
  - Interpreting SPI Decode311
  - Interpreting SPI Lister Data312
- Setup for UART/RS232 Signals313
29 UART/RS232 Triggering and Serial Decode313
- UART/RS232 Triggering315
- UART/RS232 Serial Decode318

Keysight DSOX1202A - Remote Front Panel; Remote Programming Via the Web Interface

Table of Contents

Related product manuals