EasyManuals Logo

Korg Karma User Manual

Korg Karma
305 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #242 background imageLoading...
Page #242 background image
232
The A mode functions of the REALTIME CONTROLS
are xed.
Knob1-A: LPF Cutoff (Filter LPF Cutoff: CC#74)
Control the low pass lter cutoff frequency of the lter.
Simultaneously, CC#74 will be transmitted.
Knob2-A: Resonance/HPF
(Filter Resonance/HPF Cutoff: CC#71)
Control the resonance level or the cutoff frequency of the
high pass lter. If the program Filter Type is Low Pass
Resonance, the resonance level will be controlled. If Filter
Type is Low Pass & High Pass, the cutoff frequency of the
high pass lter will be controlled. Simultaneously, CC#71
will be transmitted.
Knob3-A: EG-Intensity (Filter EG Intensity: CC#79)
Control the lter EG intensity. Simultaneously, CC#79 will
be transmitted.
Knob4-A: EG-Release (Filter, Amplier EG Release: CC#72)
Control the release time of the lter and amplier EG.
Simultaneously, CC#72 will be transmitted.
You can assign the function of an assignable switch (sepa-
rately sold Korg PS-1 option) connected to the ASSIGN-
ABLE SWITCH jack.
This setting is made in GLOBAL 6.1: Controller Foot
SW Assign (6.11a).
If you select a function that includes a CC#, that MIDI
control change message will be transmitted each time
the switch is turned on/off. (Off: 0, On: 127)
Foot Switch Assign List
Portamento SW (CC#65)
When the Mode (Oscillator Mode) (PROG 2.11a) is Sin-
gle, turning the switch on will apply portamento regardless
of the Enable (Porta. Enable) (PROG 3.11c) setting, and
turning the switch off will not apply portamento.
If Mode (Oscillator Mode) is Double, and if the Enable
(Porta. Enable) setting is the same for OSC1 and 2 (i.e.,
Enable or Disable for both OSC1 and 2), then portamento
will be applied to OSC1 and 2 when the switch is turned on,
and portamento will not be applied to OSC1 and 2 when the
switch is turned off.
If the Enable (Porta. Enable) setting is different for OSC1
and 2 (i.e., OSC1 is Enable and OSC2 is Disable, or OSC1 is
Disable and OSC2 is Enable), then portamento will be
applied to the OSC whose setting is Enable when the switch
is turned on, and portamento will be applied to neither OSC
when the switch is turned off.
Foot Switch Assign
Off The connected foot switch will not function.
Foot SW (CC#82) Alternate Modulation or Effect Dynamic Modulation can be controlled. To control these, select Foot SW:#82 for AMS or
FSW#82 for Dmod Src.
Portamento SW (CC#65) Control portamento on/off.
Sostenuto (CC#66) Control the sostenuto effect (which holds only the keys (Note No.) that were being held at the moment that the pedal
switch was turned on).
Soft (CC#67) Turn the soft pedal effect on/off.
KARMA On/Off Control the KARMA function on/off.
KARMA Latch On/Off Control KARMA Latch.
Program Up The switch can be used to select programs or combinations. When in PROG 1.1: Play, the program that follows the cur-
rently selected program will be selected. When in COMBI 1.1: Play, the combination that follows the currently selected
combination will be selected. Simultaneously, a Bank Select message and Program Change message will be transmitted.
Program Down The switch can be used to select programs or combinations. When in PROG 1.1: Play, the program that precedes the
currently selected program will be selected. When in COMBI 1.1: Play, the combination that precedes the currently
selected combination will be selected. Simultaneously, a Bank Select message and Program Change message will be
transmitted.
Song Start/Stop The switch can be used to start/stop the sequencer. Simultaneously, a MIDI Start or Stop message will be transmitted.
Song Punch In/Out If REC Setup(SEQ 1.16a) is set to Manual Punch In, the switch can be used to punch-in and punch-out when record-
ing on the sequencer.
Cue Repeat Control This can be used if in SEQ 2.1: Cue List, the Rep (Cue Edit-Repeat) (2.11b) setting of each step has been set to FS.
Turning the pedal switch on while that step is repeating will be the trigger for advancing to the next step. When the end of
the song is reached, this will advance to the next step (song).

Table of Contents

Other manuals for Korg Karma

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Korg Karma and is the answer not in the manual?

Korg Karma Specifications

General IconGeneral
Polyphony62 voices
Oscillators2 per voice
Display240 x 64 pixel backlit LCD
MIDIIn, Out, Thru
TypeWorkstation Keyboard
Keyboard61 keys
Effects2 Master effects
Sequencer16-track
ArpeggiatorYes
OutputsL/Mono, R
StorageSmartMedia

Related product manuals