Korg Karma - Dynamic MIDI Destinations

Appendices
235
Note In Z (Note In Zone)
Notes within the key zone of the KARMA module (PROG
6.1–2a, COMBI/SEQ/S.PLAY 6.1–3a) will be the source.
Use “Input” to specify the applicable KARMA module.
Note Out Z (Note Out Zone)
Notes outside the key zone of the KARMA module (PROG
6.1–2a, COMBI/SEQ/S.PLAY 6.1–3a) will be the source.
Use “Input” to specify the applicable KARMA module.
White Note
Use “Range-Btm/Top” (6.4–3a/b/c/d) to specify the range
of note numbers. Only the white notes (C, D, E, F, G, A, B)
within the specified range will be the source.
Black Note
Use “Range-Btm/Top” (6.4–3a/b/c/d) to specify the range
of note numbers. Only the black notes (C#, D#, F#, G#, A#)
within the specified range will be the source.
Velocity
Velocity values will be the source. Use “Range-Btm/Top”
(6.4–3a/b/c/d) to specify the velocity range.
Vel In Z (Velocity In Zone)
Velocity values of notes within the key zone of the KARMA
module (PROG 6.1–2a, COMBI/SEQ/S.PLAY 6.1–3a) will be
the source.
Use “Range-Btm/Top” (6.4–3a/b/c/d) to specify the veloc-
ity range. Use “Input” to specify the applicable KARMA
module.
Vel Out Z (Velocity Out Zone)
Velocity values of notes outside the key zone of the KARMA
module (PROG 6.1–2a, COMBI/SEQ/S.PLAY 6.1–3a) will be
the source.
Use “Range-Btm/Top” (6.4–3a/b/c/d) to specify the veloc-
ity range. Use “Input” to specify the applicable KARMA
module.
Dynamic MIDI Destinations
Depending on the combination of source and destination,
the selected destination may not function as you intend.
Refer to the explanations of combining sources and destina-
tions in each of the following sections, and make sure to
select sources and destinations that are appropriate for each
other.
The [M, T, C] indication shown at the right of each destination
name indicate the source operating modes (“Act-Action”) that
are valid for each destination function. (☞p.36 PROG 6.4–
3a/b/c/d: “Act” (Dyn1...4 Src Action))
Off
No function
RTParm Ctrl (RT Parms Control Assign) [M, T, C]
Use this when using a source to control GE Parameter 1...16
(6.3–1/2/3/4) or RT Parm1...8 (6.4–1/2). Set the “Asgn” of
GE Parameter1...16 or RT Parm1...8 to Dyn1...Dyn4. (☞p.33
6.3–1a: “Asgn” Dyn1, ...Dyn4)
You should normally select a source from the JS+Y
#01...JS X controller group.
This will operate irrespective of the module. The Com-
bination, Sequencer, and Song Play mode “A/B/C/D
(Param Module A/B/C/D)” (6.4–3a/b/c/d) settings
will be ignored.
Setting examples
Joystick operations in the +Y direction will control GE
Parameter1. (Program mode)
“Dyn1 Source”: JS+Y #01 (6.4–3a/b/c/d)
“Dyn1 Range-Btm/Top”: 000/127 (6.4–3a/b/c/d)
“Dyn1 Act (Src Action)”: C (6.4–3a/b/c/d)
“Dyn1 Destination”: RTParm Ctrl (6.4–3a/b/c/d)
“Dyn1 Pol (Polarity)”: + (6.4–3a/b/c/d)
GE Parameter1 “Asgn”: Dyn1 (6.4–3a/b/c/d)
Tempo [M, T, C]
Control the KARMA tempo.
You will normally select the JS+Y #01...JS X controller
group as the source.
This will operate irrespective of the module. The Com-
bination, Sequencer, and Song Play mode “A/B/C/D
(Param Module A/B/C/D)” (6.4–3a/b/c/d) settings
will be ignored.
• When “Pol” is +, you can use the controller to speed up
the tempo.
When the value of the controller selected as the source is
at the value specified for “Range-Btm,” the tempo will
be as specified by the respective mode.
When the value of the controller selected as the source is
at the value specified for “Range-Top,” the tempo will
be double the tempo specified by the respective mode.
(The tempo will not be faster than the maximum tempo
of =300 BPM.)
• When “Pol (Polarity)” is –, you can use the controller to
slow down the tempo.
When the value of the controller selected as the source is
at the value specified for “Range-Btm,” the tempo will
be as specified by the respective mode.
When the value of the controller selected as the source is
at the value specified for “Range-Top,” the tempo will
be half the tempo specified by the respective mode. (The
tempo will not be slower than the minimum tempo of
=35 BPM.)