28
6.1–3: RxFltr (Receive Filter)
Specifies whether filters will be applied to the MIDI control
data received by the KARMA module before it is passed on
(echoed) to the tone generator.
On (checked): The corresponding MIDI data will be echoed
to the tone generator.
Off (unchecked): The corresponding MIDI data will not be
echoed to the tone generator.
When the KARMA module is on, the MIDI control data
received by the KARMA module will be transmitted to the
tone generator without change. Depending on these set-
tings, you can (for example) make settings so that the
damper pedal is enabled when the KARMA module is off,
and disabled when it is on. (See the diagram below,
“KARMA Rx/Tx Filter.”)
These settings do not affect the Dynamic MIDI (PROG
6.4–3) settings. If you have specified MIDI control data
as the Dynamic MIDI source, it will be valid regardless
of these settings.
6.1–3a: Rx Filter
AfterT (After Touch) [Off, On]
Specifies whether MIDI aftertouch messages will be echoed
to the tone generator.
Bend (Pitch Bend) [Off, On]
Specifies whether MIDI pitch bend messages will be echoed
to the tone generator.
Damper (Damper CC#64) [Off, On]
Specifies whether MIDI control change message #64 Hold
(damper pedal) will be echoed to the tone generator.
JS+Y (JS+Y CC#01) [Off, On]
Specifies whether MIDI control change message #1 (internal
joystick +Y direction, or specified as the B-assignment of a
real-time control knob) will be echoed to the tone generator.
JS-Y (JS-Y CC#02) [Off, On]
Specifies whether MIDI control change message #2 (internal
joystick -Y direction, or specified as the B-assignment of a
real-time control knob) will be echoed to the tone generator.
Other CC [Off, On]
Specifies whether MIDI control change messages other than
the above will be echoed to the tone generator.
■ 6.1–3b: UTILITY
☞ “Write Combination” (1.1–1c), “Copy KARMA Module,”
“Init KARMA Module” (6.1–1c), “Select by Category”
(1.1–3b)
6.1–4: TxFltr (Transmit Filter)
Specifies whether filtering will be applied to the MIDI con-
trol data produced by the GE selected for the KARMA mod-
ule. (See the diagram below, “KARMA Rx/Tx Filter.”)
On (checked): The corresponding MIDI data will be trans-
mitted from the KARMA module.
Off (unchecked): The corresponding MIDI data will not be
transmitted from the KARMA module.
6.1–4a: Tx Filter
The GE can also automatically produce pitch bend and vari-
ous types of control change data in addition to note data.
Three envelope generators can also be used to apply time-
variant change to velocity, tempo, duration, and various
control changes such as pitch bend, JS +Y (CC#1) etc.
GE parameter group: (☞GE Guide)
Bend: Automatically generate pitch bend data in synchroni-
zation with the phrase or pattern.
CCs: Automatically generate the two control changes speci-
fied by CC-A and CC-B.
Envelopes: Use Envelope 1, Envelope 2, and Envelope 3 to
automatically generate velocity, tempo, duration, or control
changes such as pitch bend, JS +Y (CC#1) etc.
The data that is output will depend on the settings of the
parameters for the selected GE. For example, transmitting/
filtering pitch bend will produce no result if the GE has not
been designed to produce pitch bend data.
6.1–3a
6.1–3b
6.1–4a
6.1–4b
Tone
generator
KARMA Rx/Tx Filter
KARMA function
Controller
MIDI IN
KARMA Module
Dynamic MIDI
Tx Filter
Rx Filter
GE
To Next Page
Loading...
