112
■ 7.1–1(2)b: UTILITY
☞ “Memory Status”, “Solo Selected Track”, “FF.REW
Speed”, “Set Location” (1.1–1d), “DKit IFX Patch”
(COMBI 7.1–1b)
Copy Insert Effect
☞PROG 7.1–1c
However,
the MIDI control channel specified in “Control
Channel” of the 7.2: Insert FX, Setup page will not be copied.
Swap Insert Effect
☞PROG 7.1–1c
However, the MIDI control channel specified in “Control
Channel” of the 7.2: Insert FX, Setup page will not be
swapped.
7.1–3: Route (Routing)
7.1–3a: Routing Map, BUS Select
This shows the status of the insert effects: the insert effect
routing, the names of the selected effects, the on/off status,
and chaining. The effect type, on/off, and chain settings can
be made in the 7.2: Insert FX, Setup page.
T01...16: BUS Sel [DKit, L/R, IFX1...5, 1, 2, 1/2, Off]
You can specify the bus to which the program oscillators of
tracks 1–16 will be sent, while viewing a map of the current
settings.
Use the cursor keys [ ], [ ] to select the track, and use the
VALUE [ ], VALUE [ ] keys or the [VALUE] dial to set
“BUS Select” (7.1–1a/2a).
These settings can also be made from “BUS Select” (7.1–1/2).
■ 7.1–3b: UTILITY
☞ “Memory Status”, “Solo Selected Track”, “FF/REW
Speed”, “Set Location” (1.1–1c), “Copy Insert Effect,”
“Swap Insert Effect” (7.1–1b/2b), “DKit IFX Patch”
(COMBI 7.1–1b)
7.2–1: Setup
Here you can select the type of the insert effects, turn them
on/off, and make chain settings.
7.2–1a: Insert FX Setup
IFX1 — IFX5 On/Off [Off, ON]
Insert Effect 1, 5 [000...089: name]
Insert Effect 2, 3, 4 [000...102: name]
Chain [ (Off),
(ON)]
Pan(CC#8) [L000...C064...R127]
BUS Select [L/R, 1, 2, 1/2, Off]
S1 (Send1 (MFX1)) [000...127]
S2 (Send2 (MFX2)) [000...127]
These parameters are the same as in Program mode.
(
☞PROG 7.2–1)
However, this differs from Program mode in that insert
effect dynamic modulation (Dmod) and the “Pan (CC#8),”
“Send1 (MFX1),” and “Send2 (MFX2)” which follow the
insert effect are controlled on the MIDI channel specified by
“Control Channel” (7.2–1b). The control changes used are
the same as in Program mode.
The pan (CC#8) and Send 1 and 2 that you specify here are
used when playing or recording from the beginning of the
song. If you change these settings while recording, the set-
tings will be recorded as musical data, and during playback,
the settings will change accordingly. You can also change
these settings during playback. However if Pan (CC#8) and
Send 1/2 data has already been recorded, the settings will
change according to the recorded data.
If the “Status” (3.1–1(2a)) is INT or BTH, receiving
CC#8, #93, or #91 will cause the post- insert effect pan
and send 1/2 to be controlled, changing the settings.
When you change songs or return to the beginning of
the song, tracks whose “Status” is BTH, EXT, or EX2
will transmit these settings on the MIDI channel speci-
fied by “Control Channel” (7.2–1a).
7.1–3a
7.1–3b
SEQ 7.2: Insert FX
7.2–1a
7.2–1c7.2–1b
To Next Page
Loading...
Need help?
General
