256
A
Are you sure?
C
Can’t calibrate
Can’t copy/swap double size effect
Can’t open pattern Continue ?
Completed
D
Destination and source are identical
Destination from-measure within the limits of source
Destination is empty
Destination measure is empty
Destination song is empty
Disk is not empty. Cleanup directory
Are you sure?
Disk not formatted
E
Error in formatting medium
Error in reading from medium
Error in writing to medium
F
File already exists
Various messages
Meaning: This message asks you to confirm execution. To
execute press the [F8] (“OK”) key. To cancel, press
the [F7] (“Cancel”) key.
Meaning: Calibration could not be performed correctly.
Action: Try again.
Meaning: When executing Copy or Swap for an insert effect,
you attempted to place a double-size effect in
IFX1 or 5, or in an IFX whose size is restricted by
the current use of double-size effects.
Action: Make settings so that double-size effects are not
placed in IFX1 or 5 when you execute. If a double-
size effect is already being used, double-size
effects cannot be used for the preceding or follow-
ing IFX. Adjust the size structure as needed before
you execute.
Meaning: When you finished recording or editing, it was
not possible to allocate enough memory to open
the pattern that was Put into the track. (When it
must be opened automatically.) If you press the
[F8] (“OK”) key, the pattern data will be deleted,
and the recorded or edited content will be saved.
If you press the [F7] (“Cancel”) key, the recorded
or edited content will be discarded.
Meaning: Execution of the command ended normally.
Meaning: When copying or bouncing, the same cue list,
song, track or pattern was selected for both the
source and destination.
Action: Select a different cue list, song, track, or pattern
for the source and destination.
Meaning: When executing the Move Measure command for
all tracks or within the same track, the specified
destination measure is within the source range.
Action: Set a destination measure that is outside of the
source range.
Meaning: When editing, the track or pattern that was speci-
fied as the destination contains no musical data.
Action: Select a track or pattern that contains musical
data.
Meaning: The measure that was specified as the destination
contains no data.
Action: Specify a destination measure that contains data.
Meaning: The song that was specified as the copy destina-
tion or bounce destination does not exist.
Action: Execute the Create New Song command in the
dialog box that appears when a new song is
selected before copying or bouncing.
Meaning: You are attempting to delete a directory that still
contains files or sub-directories. If you press the
[F8] (“OK”) key, the directory will be deleted
along with all files or sub-directories that it con-
tains. To cancel without deleting, press the [F7]
(“Cancel”) key.
Meaning: When you attempted to perform a high-level for-
mat (quick format) of media, the media had not
been physically formatted yet.
Action: Execute the Disk mode utility menu command
“Format” to physically format the media (full for-
mat).
Meaning: An error occurred while performing a physical
format (full format) or high-level format (quick
format) of the media.
Action: Use other media.
Meaning: An error occurred while reading data from a
medium.
Action: Execute the reading operation once again. If the
same error occurs, it is possible that the data on
the disk has been damaged.
Meaning: An error occurred while writing data to a
medium. (Verify error)
Action: It is possible that the floppy disk has been physi-
cally damaged. Try another disk. Avoid using the
floppy disk that produced the error.
Meaning: When executing a Create Directory or File
Rename operation, a directory or file of the same
name already exists on the disk.
Meaning: When executing the Disk mode utility menu com-
mand “Copy” without using wild cards, the copy
destination contained a file of the same name as
the copy source.
Action: Either delete the existing directory or file, or spec-
ify a different filename.
To Next Page
Loading...
