36
6.4–3: DynMIDI (Dynamic MIDI)
Dynamic MIDI is a function that lets you use this instru-
ment’s controllers and MIDI control messages to control
specific KARMA functions.
You can take advantage of this to control KARMA in various
ways while you play. For example, Manual Advance (6.2–
2b) lets you use joystick or note-on to advance the KARMA
clock. Or you can use a foot switch to control Auto Trans-
pose, or a damper pedal to control the KARMA latch.
6.4–3a/b/c/d: Dyn MIDI1...4
Input (Dyn1...4 Input Module)
In Program mode this is fixed at A.
This is because only KARMA module [A] is used. This set-
ting cannot be changed.
Source (Dyn1...4 Source) [Off, JS+Y #01...Vel Out Z]
Indicates the controller etc. that will be the Dynamic MIDI
source.
(
☞p.234 “Dynamic MIDI Source and Distnation”)
Btm (Dyn1...4 Range-Btm) [000...127]
Specifies the lower limit for the value controlled by
“Source.”
If “Source” is Short Note, Note No., White Note, or Black
Note, the numeric value corresponds to the note numbers C-
1–G9.
Top (Dyn1...4 Range-Top) [000...127]
Specifies the upper limit for the value controlled by
“Source.”
If “Source” is Short Note, Note No., White Note, or Black
Note, the numeric value corresponds to the note numbers C-
1–G9.
Act (Dyn1...4 Src Action) [M, T, C]
Specifies the operation mode for Dynamic MIDI.
M (Momentary): The parameter will be controlled as a
switch. For example if “Source” is JS+Y #01, the parameter
will normally be off, and will be on when you move the joy-
stick.
If “Pol” (Dyn1...4 Polarity) is “+” and the source con-
troller value is “Btm (Dyn1...4 Range-Btm)” this will be
off. If the controller value is “Top (Dyn1...4 Range-
Top),” it will be on.
[Example]
When “Btm (Dyn1...4 Range-Btm)”: 000 and “Top
(Dyn1...4 Range-Top)”: 127
The controller value and the on/off status are related as
follows.
000 → 127: on at 127
127→ 000: off at 000
T (Toggle): The parameter will be controlled as a switch. For
example if “Source” is JS+Y #01, the parameter will alter-
nate between on/off each time you move the joystick.
If “Pol” (Dyn1...4 Polarity) is “+,” on and off will alter-
nate each time the source controller value exceeds the
“Top (Dyn1...4 Range-Top)” value after having passed
through the “Btm (Dyn1...4 Range-Btm)” value.
[Example]
When “Btm (Dyn1...4 Range-Btm)”: 0 and “Top
(Dyn1...4 Range-Top)”: 127
The controller value and the on/off status are related as
follows.
000 → 127: on → off at 127
127 → 000 → 127: on → off at 127
(127 → 001 → 127: no change)
C (Continuous): The parameter will be controlled continu-
ously.
The operating modes that can be selected are limited by
the “Destination.” (
☞p.234 “Dynamic MIDI Sources &
Destinations”)
Destination (Dyn1...4 Destination)
[Off, RTParm Ctrl...Buffer Latch]
Select the Dynamic MIDI control destination function.
(
☞p.235 “Dynamic MIDI Destinations”)
Pol (Dyn1...4 Polarity) [+, –, +/–, –/+]
Specifies the Dynamic MIDI polarity.
For example if you set “Pol” to + and the Source is K.Knob1,
moving the knob1 from left to right will change the value
from 0 → 127. If you set “Pol” to –, the same knob1 move-
ment will change the value from 127 → 0.
(
☞p.234 Dynamic MIDI Destination “JS X”)
■ 6.4–3e: UTILITY
☞ “Write Program” (1.1–1c), “Copy KARMA Module,” “Init
KARMA Module” (6.1–1c)
6.4–4: Name1
6.4–5: Name2
6.4–4(5)a: Knob, Switch
Knob1...8 [000: no name...]
Switch1, 2 [000: no name...]
Indicates the name for the KARMA real-time CONTROLS
knobs and keys.
Appropriate names for the functions of the KARMA real-
time CONTROLS knobs and keys have been preset.
6.4–4(5)b: UTILITY
☞ “Write Program” (1.1–1c), “Copy KARMA Module,” “Init
KARMA Module” (6.1–1c)
6.4–3a
6.4–3b
6.4–3c
6.4–3d
6.4–3e
6.4–4a
6.4–4b
To Next Page
Loading...
