1
PROG
1.1
2.12.22.33.14.14.25.15.25.36.16.26.36.47.17.27.3
1. Program mode
Use the following procedure to select the desired page
within the mode.
1 Press the [MENU] key to access the “PAGE MENU.”
The “PAGE MENU” will show an abbreviated name for
each page.
2 Use the [F1]–[F7] keys at the bottom of the page to select
the desired page. Pressing the same key repeatedly will
scroll through the various sub-pages. You can also move
by using the cursor keys [ ], [ ], [ ], [ ].
3 Press the [F8] (“Open”) key to access the page.
4 If the selected page contains two or more tab pages, press
the nearest [F1]–[F7] key below the tabs to select the
desired page.
Other ways to select a page
• You can also move to the desired page by holding down
the [MENU] key and using numeric keys [0]–[9] to enter
a two-digit page number. For example if you wish to
access the 5.3: Ed-LFOs page, hold down the [MENU]
key and consecutively press numeric keys [5] and then
[3].
• By holding down the [MENU] key and using the cursor
keys [ ](–) or [ ](+), you can step through the pages
forward or backward in the order of 1.1→2.1→2.2→3.1,
etc.
PROG PAGE MENU
Play 1.1: Play Select and play programs. Use the Per-
formance Editor for easy editing, and to
select KARMA GE. (
☞p.2)
Basic 2.1: Ed-Basic Set basic program parameters such as
Oscillator and Multisample. (
☞p.7)
Ctrl 2.2: Ed-Ctrl Controller settings. (
☞p.10)
OSC 2.3: Ed-OSC This will be displayed when you select
bank F if the optional EXB-MOSS is
installed. OSC settings for the MOSS
tone generator. (
☞p.11)
Pitch 3.1: Ed-Pitch Pitch settings. Pitch EG settings.
(
☞p.11)
Flt1 4.1: Ed-Filter1 Filter 1 (tone) settings. Filter EG set-
tings. (
☞p.15)
Flt2 4.2: Ed-Filter2 Filter 2 (tone) settings. Filter EG set-
tings. (
☞p.20)
Amp1 5.1: Ed-Amp1 Amp 1 and Amp 2 (volume) settings.
Amp EG, pan (position) settings.
(
☞p.20)
Amp2 5.2: Ed-Amp2
LFO 5.3: Ed-LFOs Type and speed settings etc. for the
two LFOs provided for each oscillator.
(Make settings in the pitch, filter, and
amp pages to specify the depth of the
LFO settings you make here.) (
☞p.24)
Amp 5.1: Ed-Amp This will be displayed when you select
bank F if the optional EXB-MOSS is
installed. Amp (volume) settings. Amp
EG, pan (position) settings. (
☞p.23)
EG 5.2: Ed-EGs
KARM 6.1: Ed-KARMA KARMA GE selection, key zone
parameters, MIDI filter settings.
(
☞p.26)
K Mdl 6.2: Ed-KARMA Mdl Module parameter settings (transpose,
pitch range of generated phrase, trig-
ger etc.) (
☞p.29)
K GE 6.3: Ed-KARMA GE GE parameter settings and assign-
ments to KARMA real-time controls
(
☞p.32)
K RT 6.4: Ed-KARMA RT KARMA RT parameters, Dynamic MIDI
settings. (
☞p.34)
BUS 7.1: Ed-BUS Select the BUS and master effect send
level for the oscillator output. (
☞p.37)
IFX 7.2: Ed-InsertFX Insert Effect routing, selection and set-
tings. (
☞p.38)
MFX 7.3: Ed-MasterFX Master Effect selection and settings.
Master EQ settings. (
☞p.40)
To Next Page
Loading...
Need help?
General
