Meggitt VM600 - APPENDIX C: MPC4 PROFINET SLOT DEFINITIONS

VM600 networking manual MAVM600-NET/E C - 1
Edition 9 - February 2018
APPENDIX C: MPC4 PROFINET SLOT DEFINITIONS
APPENDIX C: MPC4 PROFINET
SLOT DEFINITIONS
MPC4 card slot definitions for PROFINET are illustrated using the following extract from a
typical modbusDefault.cfg configuration file for an MPC4 card in slot 3 of a VM600 rack.
...
[GLOBAL]
...
IS_PROFINET_ACTIVED = YES
[MAPPING]
/////////////////////////////////////////////////
///////////////// Slot3 ////////////////////////
/////////////////////////////////////////////////
///////////////// Alarm and Status //////////////
// Slot3, Channel 1, Output 1
$MPC4S3C1O1Used = Slot3:MPC4:Config:C1:O1:Used
$MPC4S3C1O1Apos = Slot3:MPC4:C1:O1:A+
$MPC4S3C1O1Aneg = Slot3:MPC4:C1:O1:A-
$MPC4S3C1O1Dpos = Slot3:MPC4:C1:O1:D+
$MPC4S3C1O1Dneg = Slot3:MPC4:C1:O1:D-
$MPC4S3C1O1SOK = Slot3:MPC4:Status:C1:SOK
$MPC4S3C1O1UsedAndApos = AND($MPC4S3C1O1Used, $MPC4S3C1O1Apos)
$MPC4S3C1O1UsedAndAneg = AND($MPC4S3C1O1Used, $MPC4S3C1O1Aneg)
$MPC4S3C1O1UsedAndDpos = AND($MPC4S3C1O1Used, $MPC4S3C1O1Dpos)
$MPC4S3C1O1UsedAndDneg = AND($MPC4S3C1O1Used, $MPC4S3C1O1Dneg)
$MPC4S3C1O1UsedAndSOK = AND($MPC4S3C1O1Used, $MPC4S3C1O1SOK)
// Slot3, Channel 1, Output 2
$MPC4S3C1O2Used = Slot3:MPC4:Config:C1:O2:Used
$MPC4S3C1O2Apos = Slot3:MPC4:C1:O2:A+
$MPC4S3C1O2Aneg = Slot3:MPC4:C1:O2:A-
$MPC4S3C1O2Dpos = Slot3:MPC4:C1:O2:D+
$MPC4S3C1O2Dneg = Slot3:MPC4:C1:O2:D-
$MPC4S3C1O2SOK = Slot3:MPC4:Status:C1:SOK
$MPC4S3C1O2UsedAndApos = AND($MPC4S3C1O2Used, $MPC4S3C1O2Apos)
$MPC4S3C1O2UsedAndAneg = AND($MPC4S3C1O2Used, $MPC4S3C1O2Aneg)
$MPC4S3C1O2UsedAndDpos = AND($MPC4S3C1O2Used, $MPC4S3C1O2Dpos)
$MPC4S3C1O2UsedAndDneg = AND($MPC4S3C1O2Used, $MPC4S3C1O2Dneg)
$MPC4S3C1O2UsedAndSOK = AND($MPC4S3C1O2Used, $MPC4S3C1O2SOK)