Nord Drivesystems NORDAC FLEX SK 210E Series User Manual

NORDAC FLEX (SK 200E ... SK 235E) – Users Manual for Frequency Inverters
222 BU 0200 en-3118
Pos: 63 2 /Anlei tung en/El ektr onik/FU und Star ter/6 . Meld ungen zum Betr iebsz usta nd/Dars tell ung der Meldu ngen @ 3\ mod_1361802708455_388.docx @ 59827 @ 2 @ 1
6.1 Display of messages
Pos: 63 3 /Anlei tung en/El ektr onik/FU und Star ter/6 . Meld ungen zum Betr iebsz usta nd/Dars tell ung der Meldu ngen - LED A nzei gen @ 3\ mod_1361796228478_388.docx @ 59694 @ 5 @ 1
LED displays
The status of the FI is indicted by integrated status LEDs, which are visible from the outside in the
state as delivered. According to the type of FI, this is a two-colour LED (DS = DeviceState) or two
single-colour LEDs (DS DeviceState and DE = DeviceError).
Meaning:
Green indicates readiness and the present of mains voltage. In operation, the
level of overload at the FI output is shown with an increasingly rapid flashing
code.
Red
Signals the presence of an error by flashing according to the number
code of the error. This flashing code (e.g.: E003 = 3x flashing) indicates the
error groups.
Pos: 63 4 /Anlei tung en/El ektr onik/FU und Star ter/6 . Meld ungen zum Betr iebsz usta nd/Dars tell ung der Meldu ngen - Si mpleB ox / Con trolBo x Anzeig e [SK x xxE] @ 3\mod_1361801795294_3 88. docx @ 5 980 2 @ 5 @ 1
SimpleBox - display
The SimpleBox displays an error with its number and the prefix "E". In addition, the current fault can
be displayed in array element [-01] of parameter (P700). The last error messages are stored in
parameter P701. Further information on inverter status at the time that the error occurs can be found
in parameters P702 to P706 / P799.
If the cause of the error is no longer present, the error display in the SimpleBox flashes and the error
can be acknowledged with the Enter key.
In contrast, warning messages are prefixed with "C" ("Cxxx") and cannot be acknowledged. They
disappear automatically when the reason for them is no longer present or the frequency inverter has
switched to the "Error" state. Display of the message is suppressed if the warning appears during
parameterisation.
The present warning message can be displayed in detail at any time in array element [-02] of
parameter (P700).
The reason for an existing disabled switch on cannot be displayed with the SimpleBox.
Pos: 63 5 /Anlei tung en/El ektr onik/FU und Star ter/6 . Meld ungen zum Betr iebsz usta nd/Dars tell ung der Meldu ngen - ParameterBox - Anzei ge @ 3\mod_1361801566355_388.docx @ 59779 @ 5 @ 1
ParameterBox display
The ParameterBox displays the messages in plain text.
Pos: 63 6 /Anlei tung en/El ektr onik/FU und Star ter/6 . Meld ungen zum Betr iebsz usta nd/Diag nos e LEDs/D iag nose LED s am Ger ät (Über schrift+) [SK 1xxE, SK 2xxE, SK xxxE-FD S] @ 1\mod_1343201905326_388.docx @ 36935 @ 2 @ 1
6.2 Diagnostic LEDs on device
The device generates operating status messages. These messages (warnings, errors, switching
statuses, measurement data) can be displayed with parametrisation tools ( Section 3.1.1 "Control
and Parametrisation Boxes / Software") (Parameter group P7xx).
To a limited extent, the messages are also indicated via the diagnostic and status LEDs.
Pos: 63 7 /Allg emein/ Allg emeing ültig e Mod ule/---------Sei tenumbr uch ko mpakt --------- @ 13\mod_1476369695906_0.docx @ 2265495 @ @ 1

Nord Drivesystems NORDAC FLEX SK 210E Series Specifications

General

Brand	Nord Drivesystems
Model	NORDAC FLEX SK 210E Series
Category	Inverter
Language	English