1 General
BU 0200 en-3118 25
Pos: 36.1 1 / Anlei tu ngen /El ektr oni k/FU un d Start er/1 . Allgem eines /Sic herh eits- un d Instal latio nshin weis e und War n- Gefahrenhinweise/neu/Sicherheits- un d Inst allati onshi nweis e - Einzel pu nkte/ 4 _e. B etri eb (Sic her heit shi nwei se ( U mrich ter) ) @ 19\ mod_1508746864938_388.docx @ 2368741 @ @ 1
Operation
Where necessary, systems in which the devices are installed must be equipped with additional
monitoring and protective equipment according to the applicable safety requirements (e.g. legislation
concerning technical equipment, accident prevention regulations, etc.).
All covers must be kept closed during operation.
With certain setting conditions, the device or the motor which is connected to it may start automatically
when the mains are switched on. The machinery which it drives (press / chain hoist / roller / fan etc.)
may then make an unexpected movement. This may cause various injuries, including to third parties.
Before switching on the mains, secure the danger area by warning and removing all persons from the
danger area.
Due to its operation, the device produces noises within the audible frequency range. These noises
may cause long-term stress, discomfort and fatigue, with negative effects on concentration. The
frequency range or the noise can be shifted to a less disturbing or almost inaudible range by
adjustment of the pulse frequency. However, this may possibly result in derating (lower power) of the
device.
Pos: 36 .12 /A nleitu ngen/ Elektr onik /FU und St art er/1. Al lgemei nes/ Sich erheits - und Ins tall ations hinw eise un d Warn- Gefahrenhinweise/neu/Sicher heits - un d Inst allati onshi nweis e - Einzel pu nkte/ 4 _f. W art ung, Ins tan dhal tu ng u nd A uß erb etrie bna hm e (Si cher h eitshi n weis e) @ 19 \mod_1508748695495_388.docx @ 2368881 @ @ 1
Maintenance, repair and decommissioning
Installation, maintenance and repair work must not be carried out unless the device has been
disconnected from the voltage and at least 5 minutes have elapsed since the mains was switched off!
(Due to charged capacitors, the equipment may continue to carry hazardous voltages for up to
5 minutes after being switched off at the mains). Before starting work it is essential to check by
measurement that all contacts of the power plug connections or the connection are voltage-free.
For further information, please refer to the manual for the device.
Pos: 36 .13 /A nleitu ngen/ Elektr onik /FU und St art er/1. Al lgemei nes/ Sich erheits - und Ins tall ations hinw eise un d Warn- Gefahrenhinweise/neu/Sicherheits- und I nstal lati onshi nweis e - Einzel pu nkte/ 4_g . E ntsor gu ng ( Sic her hei tshi nw eise) @ 19\ mod_1508749472287_388.docx @ 2368986 @ @ 1
Disposal
The product and its parts and accessories must not be disposed of as domestic waste. At the end of
its life, the product must be properly disposed of according to the local regulations for industrial waste.
In particular, this product contains integrated semiconductor circuits (PCBs and various electronic
components, including high power capacitors). In case of incorrect disposal there is a risk of formation
of toxic gases, which may cause contamination of the environment and direct or indirect injuries (e.g.
chemical burns). In the case of high power capacitors, there is also a risk of explosion, with the
associated risk of injury.
Pos: 36 .14 /A nleitu ngen/ Elektr onik /FU und St art er/1. Al lgemei nes/ Sich erheits - und Ins tall ations hinw eise un d Warn- Gefahrenhinweise/neu/Sicherheits- und I nstal lati onshi nweis e - Einzel pun kte/ 5. Explosionsgefährdete Umgebung (ATEX) [SK 1xxE, SK 2xxE] @ 21\mod_1528787805877_388.docx @ 2425680 @ @ 1
5. Potentially explosive environment (ATEX, EAC Ex)
In order to operate or carry out installation work in potentially explosive environments (ATEX,
EAC Ex), the device must be approved and the relevant requirements and notes from the manual of
the device must be complied with.
Failure to comply can result in the ignition of an explosive atmosphere and fatal injuries.
• Only persons who are qualified, i.e. trained and authorised for all assembly, service,
commissioning and operation work on association with explosion hazard environments may work
with the devices described here (including the motors, geared motors, any accessories and all
connection technology).
• Explosive concentrations of dust may cause explosions if ignited by hot or sparking objects. Such
explosions may cause serious or fatal injuries to persons or severe material damage.
To Next Page
Loading...
Need help?
General
