122
List of Parameters Section 6-6
6-6 List of Parameters
CH
CH
Level Key for 1 second min.
CH
CH
Parameter
Initialize
α
MV Upper Limit
Scaling
Upper Limit
Input Type
Scaling
Lower Limit
Decimal Point
˚C/˚F Selection
Set Point
Upper Limit
Set Point
Lower Limit
PID/OnOff
Heating Control
Period
Control Output 2
Allocation
Current Output
Type
Voltage Output
Type
Alarm 1 Latch
Cold Junction
Compensation
Method
To top of initial setting level
Return to top of advanced function setting level
Communi-
cations
Data Length
CH
ch2: ch1:
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Possible by
setting
password
(−169)
Advanced function
setting level
Initial setting level
Level Key
Level Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Mode Key
Communication
setting level
Cooling Control
Period
Direct/Reverse
Operation
Alarm 1 Type
Alarm 2 Type
Alarm 3 Type
Control Output 1
Allocation
Auxiliary Output 1
Allocation
Auxiliary Output 2
Allocation
Auxiliary Output 3
Allocation
Auxiliary Output 4
Allocation
Operation after
Power ON
OUT1 Transfer
Output Upper Limit
OUT1 Transfer
Output Lower Limit
OUT2 Transfer
Output Upper Limit
OUT2 Transfer
Output Lower Limit
SUB3 Transfer
Output Upper Limit
SUB3 Transfer
Output Lower Limit
SUB4 Transfer
Output Upper Limit
SUB4 Transfer
Output Lower Limit
Number of
Multi-SP Uses
Event Input
Allocation
Multi-SP Uses
SP Ramp Set Value
Standby Sequence
Reset Method
Alarm 1 Open
for Alarm
Alarm 1 Hysteresis
Alarm 2 Open
for Alarm
Alarm 2 Hysteresis
Alarm 3 Open
for Alarm
Alarm 3 Hysteresis
HBA Used
Heater Burnout
Latch
Heater Burnout
Hysteresis
MV Lower Limit
Input Digital Filter
Additional PV Display
Additional
Temperature Input
Shift Value Display
Alarm 2 Latch
Alarm 3 Latch
Communi-
cations
Stop Bit
Communi-
cations
Parity
Communi-
cations
Response
Wait Time
Level Key
for less than 1 second
(See note 2.)
(See note 2.)
Sensor Error Indicator
Advanced Function
Setting Level
(See note 2.)
Temperature Input
Shift Type
(See note 2.)
Input Error Output
(See note 1.)
(See note 1.)
(See note 1.)
(See note 2.)
(See note 2.)
(See note 2.)
(See note 2.)
(See note 2.)
(See note 2.)
(See note 2.)
(See note 2.)
(See note 2.)
The following display indicates that ch1
and ch2 have different parameter settings.
CH
Press the Button to switch
between the data for ch1 and ch2.
(See note 2.)
(See note 2.)
The following diagram shows the parameters that can be set from
the E5ZN-SDL Setting Display Unit. Some data is not displayed as
it is protected or is subject to usage conditions. A password must
be entered for access to the advanced function setting level.
1. Indicates parameters that are displayed for pulse output models only.
2. Indicates parameters that are displayed for analog output models only.
Note
To Next Page
Loading...
