Oval ALTI mass CA00A - Page 3

L
--
740
--
28
--
E

6.8 A Boss for Pressure Relief Device - Its Use ....................................................................... 52
6.9 Separately Mounted Transmitter Installation ......................................................................... 52
6.10 How to Change Transmitter Orientation .............................................................................. 52
6.11 How to Change Transmitter Display Orientation..................................................................54
7. WIRING INSTRUCTIONS ......................................................................................................57
7.1 Wiring Connections ............................................................................................................... 57
7.1.1 Power and output signal connections (both integrally and separately mounted models) ....57
7.1.2 Connections between separately mounted sensor unit and transmitter .......................... 58
7.2 Power Supply Lines and Ground Terminal ............................................................................ 58
7.3 Analog Output Wiring ............................................................................................................ 58
7.4 Pulse Output Wiring .............................................................................................................. 59
7.5 Status Output Wiring ............................................................................................................. 59
7.6 Status Input Wiring ................................................................................................................60
7.7 Communication Line Wiring (option) ..................................................................................... 60
7.8 Recommended Cables condition ......................................................................................... 60
7.9 Terminal Identification of Separately Mounted Transmitter....................................................61
7.10 Wiring Diagram ....................................................................................................................62
7.10.1 Transmitter power and output signal wiring ................................................................... 62
7.10.2 Separately mounted sensor unit and transmitter wiring ................................................63
7.11 How to Change Cable Entry Orientation of Terminal Box (Separately Mounted Type) ....... 64
8. OPERATION ........................................................................................................................... 66
8.1 Flushing the Piping Assembly ............................................................................................... 66
8.2 Confirming the Sensor Unit for Correct Installation ...............................................................66
8.3 Leak Check ........................................................................................................................... 66
8.4 Supplying the Power ............................................................................................................. 66
8.5 Measurement Line Startup ....................................................................................................66
8.6 Warm-up ............................................................................................................................... 66
8.7 Zeroing Procedure .................................................................................................................66
8.8 Readying for Operation ......................................................................................................... 66
9. DESCRIPTION OF INCORPORATED FUNCTIONS .......................................................67
9.1 Display ...................................................................................................................................67
9.1.1 Description of display ..................................................................................................... 67
9.1.2 Switch operation ..............................................................................................................68
9.1.3 Viewing the variables ...................................................................................................... 69
9.2 Viewing the Parameters and Description .............................................................................. 71
9.2.1 Viewing the setup menu .................................................................................................. 71
9.2.2 Transition chart of view (1) .............................................................................................. 72
9.2.3 Transition chart of view (2) .............................................................................................. 74
9.2.4 Transition chart of view (3) .............................................................................................. 76
9.2.5 Transition chart of view (4) .............................................................................................. 78
9.2.6 Transition chart of view (5) .............................................................................................. 80
9.2.7 Transition chart of view (6) .............................................................................................. 82
9.3 Parameter Value Entry ..........................................................................................................84
9.4 Parameter Selection ..............................................................................................................85
9.5 Password Function ................................................................................................................86
9.5.1 Password function setup ................................................................................................. 86
9.6 Self-diagnostic Capabilities ................................................................................................... 87
9.6.1 Probe check .....................................................................................................................87
9.6.2 Drive coil check ............................................................................................................... 88
9.6.3 Transmitter check ............................................................................................................ 89
9.6.4 Pipeline vibration check (at zero flow) .............................................................................90
9.6.5 Pipeline oscillation check (at normal flow) ....................................................................... 91
9.7 Simulated Signal Input/Output Capabilities ...........................................................................92
9.7.1 Analog output .................................................................................................................. 92
9.7.2 Pulse output .................................................................................................................... 93
9.7.3 Status output ................................................................................................................... 94
9.7.4 Status input ......................................................................................................................95
9.8 Zeroing Function ................................................................................................................... 96
9.8.1 Through LCD display switches ........................................................................................96
9.8.2 Through status input signal ............................................................................................. 97
9.8.3 Through Link Top communication ....................................................................................97
9.9 Analog Trim Function ............................................................................................................. 98
9.10 Reset Function .................................................................................................................... 99
9.11 View Variables Screen Setup ............................................................................................ 100
9.12 Pulse Output Function .......................................................................................................101
9.12.1 Pulse output 1 ..............................................................................................................101
9.12.2 Pulse output 2 ..............................................................................................................101
9.12.3 Bidirectional pulse output .............................................................................................. 102
9.12.4 Double pulse input ..........................................................................................................103
9.13 Analog Output Function ........................................................................................................104
9.14 Status Output Function .........................................................................................................105
9.14.1 Status output (Error Status) ............................................................................................105
9.14.2 Bidirectional flow direction output (Bi Direction) .............................................................105
9.14.3 H/L alarm output (H/L Alarm) ..........................................................................................106