Ross Acuity 4810AR-002 - Page 12

To Enable a Bus to Use
SmartConversion............................................85
To Lock a Conversion Loop to a Bus.....................86
To Set the Fade to Black Display Mode.................86
Status.................................................................87
Software Version...................................................................87
To View Software Version Information...................87
Switcher Status.....................................................................87
To View the Switcher Status Pages.......................87
Software Status Overview......................................87
System Status Overview........................................87
Frame Boards........................................................88
Status and Warnings.............................................................88
To View the Status of the Switcher........................88
Status Definitions...................................................88
Input Status...........................................................................89
To View the Input Status........................................89
Non-Sync Status...................................................................89
To View the Non-Sync Status................................89
Bus Selection Status.............................................................90
To View the Bus Selection Status..........................90
Tx/Rx Status..........................................................................90
To View the Tx/Rx Status of the Control Panel
Ports...............................................................90
To View the Serial Tx/Rx Errors.............................90
FSFC Status..........................................................................90
To View the FSFC Status.......................................90
Running Custom Controls Status..........................................90
To View the Custom Controls Currently
Running..........................................................90
Options..............................................................91
To Install a Serial Number.....................................................91
Installed Options....................................................................91
To Install a Software Option..................................................91
To Backup Options Codes.....................................................91
To Recall Options Codes.......................................................92
Calibration.........................................................93
To Calibrate the Fader and Positioner...................................93
To Turn Button LED Calibration Off.......................................93
Control Panel Diagnostics...............................94
Installed Control Panel Boards..............................................94
To View the Installed Control Panel
Boards............................................................94
Module Tests.........................................................................94
To Perform a Button Color Test..............................94
To Perform a Button Function Test.........................94
To Perform a Stuck Button Test.............................94
To Perform a Fader Test........................................94
To Perform a Positioner Test..................................94
To Perform a Control Panel Display Test...............95
To Perform a Knob Test.........................................95
To Perform a Module Memory Test........................95
To Perform an Audio Fader Test............................95
Control Panel Power Supply Failure.....................................95
To Identify a Failed Power Supply..........................95
To Identify a Failed Cooling Fan............................96
Panel Communications Hub Tests........................................96
To Perform a PCH Tx/Rx Test................................96
To Perform an LVDS Test.......................................96
To Perform a Tally Test...........................................97
To Perform a PCI Bridge Test................................97
Touchscreen Tests.................................................................97
To Perform a Pattern Test on the
Touchscreen...................................................97
To Perform a Draw Test on the
Touchscreen...................................................97
To Perform the Burn Mode Test of the
Touchsreen.....................................................97
Frame Diagnostics...........................................98
Installed Frame Boards.........................................................98
To View the Installed Frame Boards......................98
Frame Diagnostic Tests.........................................................98
To Perform a DIP Switch Test................................98
To Perform a Frame Tx/Rx Test.............................98
To Perform a GPI Test............................................98
To Perform a Tally Test...........................................98
To Perform a Contact Closure Test........................98
Frame Fan Failure.................................................................99
To Identify a Failed Fan..........................................99
Frame Power Supply Failure.................................................99
To Identify a Failed Power Supply..........................99
Port Monitoring and Logs..............................101
Port Monitor Files................................................................101
To Monitor a Serial Port.......................................101
To Monitor an Ethernet Port.................................101
To Download Port Monitor Data Files..................101
Device Logging....................................................................101
To Set the Device Log Level................................102
Frame Logs.........................................................................102
To Collect Frame Logs.........................................102
To Delete Frame Logs..........................................102
To Cycle Frame Logs...........................................102
Panel Logs..........................................................................102
To Collect Panel Logs..........................................103
Sending Files to Ross Video...............................................103
To Send Files To Ross Video...............................103
Switcher Maintenance....................................104
Backup and Restore............................................................104
To Backup the Switcher Hard Drive.....................104
To Restore the Switcher Hard Drive....................104
Configuration Files..............................................................104
To Download Configuration Files.........................104
To Upload Configuration Files..............................105
Force Panel Upgrade..........................................................105
To Force an Upgrade of the Control
Panel.............................................................105
Still-Store Permissions........................................................105
To Clean Still-Store Permissions..........................105
Dusting Mode......................................................................105
xii • Contents — Acuity Setup Manual (v9.2)