Aux Bus Names
Allows you to select whether the switcher uses the aux
bus number or name in the menu system and bus map.
Press HOME > Setup > Personality and use the
Option knob to select AuxBusNames.
• Aux N:M — use the number of the aux bus (for
example, Aux 4:3).
• Name — use the name of the aux bus.
Bank 0 Lit
Sets whether or not the BANK button on the Memory
Modules is lit when bank 0 is selected.
Press HOME > Setup > Personality and use the
Option knob to select Bank 0 Lit.
• Off — the BANK button is not lit when bank 0 is
selected.
• On — the BANK button is lit when bank 0 is selected
in the Memory Module, or Global Memory Module.
BKGD Double Press
Allows you to have a double-press of the BKGD or KEY
X button on a Transition Module set up the next transition
to take the keys off-air. Double-press the BKGD button
to select background and all on-air keys as part of the
next transition. Double-press any KEY X button to select
all on-air keys as part of the next transition, and not
include background.
Press HOME > Setup > Personality and use the
Option knob to select BKGD Double Press.
• Off — not include the on-air keys with the next
transition when the BKGD or KEY X button is
double-pressed.
• On — include all on-air keys with the next transition
when the BKGD or KEY X button is double-pressed.
CC/Macro Attachments
Sets whether or not custom controls that are attached to
control panel buttons using the Attach Custom Controls
Menu are run when the button is pressed.
Press HOME > Setup > Personality and use the
Option knob to select CC/Macro Attachments.
• Off — custom controls attached to control panel
buttons are not run when the button is pressed.
• On — custom controls attached to control panel
buttons are run when the button is pressed.
CC Global Recall
Sets whether or not the RECALL CLIP/CC button on
the Global Memory module can be used to run a custom
control.
Press HOME > Setup > Personality and use the
Option knob to select CC Global Recall.
• Off — only allow clips to be recalled from the Global
Memory module using the RECALL CLIP/CC button.
• On — only allow custom controls to be run from the
Global Memory module using the RECALL CLIP/CC
button.
CC Held/Paused Display
Sets whether the mnemonic of a custom control show
Held or Pause when the custom control is at that state
(Held/Paused), only shows the name of the custom
control (CC Name), or shows both the Held or Paused
and the name of the custom control (Both).
Press HOME > Setup > Personality and use the
Option knob to select CC Held Display.
• Held/Paused — shows Held or Paused in the
mnemonic for a custom control that is at a held or
paused state.
• CC Name — shows the name of the custom control
when the custom control is at a held or paused state.
• Both — shows both the name of the custom control
and Held or Paused when the custom control is at a
held or paused state.
CC Memory State
Sets whether the Effects Dissolve and Keys Only settings
of a memory are used when the memory is recalled with
a custom control. Recalling the memory directly is not
affected. This allows the custom control to recall a single
memory and override the Effects Dissolve and Keys Only
on or off settings of how the memory was stored. This
setting overrides the Auto Recall personality option.
Press HOME > Setup > Personality and use the
Option knob to select CC Memory State.
• Off — Effects Dissolve and Keys Only are recalled
how they are stored in the memory.
• On — Effects Dissolve and Keys Only can be
overridden in a custom control that recalls the
memory.
Clear Bus Hold on All-All
Sets whether or not the Bus Hold selection on a bus is
cleared when a soft-reset is performed.
Press HOME > Setup > Personality and use the
Option knob to select Clear Bus Hold.
42 • Personality — Acuity Setup Manual (v9.2)
To Next Page
Loading...
