9-44
Positional deviation measurement
9
REGST NO. 0(0~7)
X COORD.(MDL0)
X=176.0 OK
Y COORD.(MDL0)
Y=322.0 OK
X DEVIAT (MDL0) X=+000.0
OK
Y DEVIAT (MDL0) Y=+000.0
OK
MATCH (MDL0) +
10000 OK
(1-point search)
REGST NO. 0(0~7)
X COORD.(MDL0)
X=176.0 OK
Y COORD.(MDL0)
Y=322.0 OK
X DEVIAT (MDL0) X=+000.0
OK
Y DEVIAT (MDL0) Y=+000.0
OK
MATCH (MDL0) +
10000 OK
ANGULAR DEVIT +
001.7゜OK
X COORD.(MDL1) X=534.0
OK
Y COORD.(MDL1) Y=480.0
OK
X DEVIAT (MDL1) X=+001.0
OK
Y DEVIAT (MDL1) Y=+001.0
OK
(1-point search + 1-point edge)
REGST NO. 0(0~7)
X COORD.(MDL0)
X=176.0 OK
Y COORD.(MDL0)
Y=322.0 OK
X DEVIAT (MDL0) X=+000.0
OK
Y DEVIAT (MDL0) Y=+000.0
OK
(1-point edge)
REGST NO. 0(0~7)
X COORD.(MDL0)
X=176.0 OK
Y COORD.(MDL0)
Y=322.0 OK
X DEVIAT (MDL0) X=+000.0
OK
Y DEVIAT (MDL0) Y=+000.0
OK
ANGULAR DEVIT +
001.7゜OK
X COORD.(MDL1) X=534.0
OK
Y COORD.(MDL1) Y=480.0
OK
X DEVIAT (MDL1) X=+001.0
OK
Y DEVIAT (MDL1) Y=+001.0
OK
(2-point edge)
· By moving the cursor to REG-CHNG (change registration), and pressing the up key, it is possible to see
the measurement results for different registration numbers and numerical calculations. This is done by
scrolling through them in this order: registration numbers 0→1→2→3…7. These are followed by the
results of the numerical calculations N00 to N15. The measurements screen also has this feature.
Pressing the down key in these situations will scroll back through the results in the opposite order.
· Unregistered numbers will be skipped.
· When there are no recorded numbers (other than those currently on display) or if no measurement has
actually been carried out, then it will not be possible to scroll through the data.
· The displays for other modes are as follows.
Continued from the previous page
F H C1ALLC2NO
VX.X
(TYPE00)
OK
MEAS. XXXXXXms
MEAS0 CAM1 POS-DEVIATION
REGST NO. 0(0~7)
X COORD.(MDL0)
X=176.0 OK
Y COORD.(MDL0)
Y=322.0 OK
X DEVIAT (MDL0) X=+000.0
OK
Y DEVIAT (MDL0) Y=+000.0
OK
MATCH (MDL0) +
10000 OK
ANGULAR DEVIT +
001.7゜OK
X COORD.(MDL1) X=534.0
OK
Y COORD.(MDL1) Y=480.0
OK
X DEVIAT (MDL1) X=+001.0
OK
Y DEVIAT (MDL1) Y=+001.0
OK
MATCH (MDL1) +
09999 OK
Final evaluation result
Measuring time
Registration number
Degree of match with the
reference image for model 0
Detection coordinates in the
reference image for model 0
[Display of the measured
results]
Amount of deviation from
the reference image for model 0
Only displayed for a 2 point search
Degree of match with the
reference image for model 1
Detection coordinates in the
reference image for model 1
Amount of deviation from
the reference image for model 1
X0~6
:
Y0~7
:
BUSY
:
Model 0
Model 1
MSR-CHNG REG-CHNG PC-MONTR SET-SCRN MANL-TYP-CHG
Pressing the TRG/BRT key will display the results of a positional deviation measurement for the new
image that you have recorded.
Shown below is the display when a 2 point search has been specified.
To Next Page
Loading...
Need help?
General