SICK FLOWSIC200 - Assembly and Installation

122 pages

Save Page as PDF

To Next Page

To Previous Page

Assembly and installation

FLOWSIC200 · Operating Instructions · 8013271/1CJ9/V2-0/2022-01 · © SICK Engineering GmbH 31

FLOWSIC200

3 Assembly and installation

Project planning

Assembly

Installation

Main Page

Table of Contents4
Important Information7
Function of this Document8
Scope of Application8
Target Groups8
Data Integrity9
Intended Use9
Safety Information and Protective Measures10
General Information10
Basic Safety Information11
Recognizing Malfunctions11
Preventing Damage12
Product Description13
System Overview, Functional Principle14
System Overview14
Communication between Sender/Receiver Units and Control Unit15
Functional Principle16
System Components18
FLSE200 Sender/Receiver Unit18
Bracket for Sender/Receiver Unit19
MCU Control Unit20
Connection Cable25
Mounting Kit26
Computations27
Flow Velocity Calibration27
Temperature Calibration27
Response Time27
Check Cycle28
Zero Point Check28
Span Test28
Check Cycle Output on the Analog Output29
Assembly and Installation31
Project Planning32
Planning Steps32
Requirements for the Installation Location for the Sender/Receiver Units32
Assembly34
Fitting the Brackets for the Sender/Receiver Units34
Setting the Bus Systems35
Check the Termination35
Bus Addressing Via Hardware Setting36
Fitting the Sender/Receiver Units37
Aligning the Sender/Receiver Units39
Installing the Junction Box40
Installing the MCU Control Unit41
Installation42
General Information, Prerequisites42
Information on Wiring43
Cable Specification (Connection of a Measuring Point)44
Cable Lengths45
Connecting Sender/Receiver Units and Junction Boxes45
Connecting the Control Unit with Wall Housing46
Connecting the Control Unit in the 19" Housing51
Commissioning and Parameterization55
Basics56
General Information56
Installing the SOPAS ET Program56
Connecting to the Device58
Changing the Language58
Connecting to the Device Via the "Device Family" Mode59
Search Settings)59
Connect to the Device with Advanced Mode61
Information on Using the Program64
Standard Commissioning Procedure67
Assigning Sensors68
Activating Connected Sender/Receiver Units69
Assigning the Measuring System to the Measuring Location70
Entering System Data71
Setting the Check Cycle72
Configuring the Analog Output73
Configuring the Analog Inputs75
Configuring the Limit Value Relay76
Setting the Response Time (Damping Time)77
Output Flow Direction78
Data Backup79
Starting Normal Measuring Operation82
Advanced Commissioning85
Parameterizing Optional Analog and Digital Output Modules85
Analog Outputs85
Digital Outputs86
Assigning and Configuring Limit Value Switches to Optional Digital Outputs88
Configuring Optional Interface Modules89
General Information89
Changing the Field Bus Address for the Profibus Module90
Configuring the Ethernet Module91
Calibrating Velocity and Temperature Measurement92
Bus Addressing Using SOPAS ET93
Configuring Automatic System Restart94
Operating / Parameterization with the LC Display Option95
General Information on Use95
Menu Structure96
Configuring96
Mcu96
Sender/Receiver Units98
Changing the Display Settings with SOPAS ET99
Maintenance101
General102
Measures to be Taken When Cleaning the Tunnel103
Malfunctions105
General Information106
Implausible Measured Values107
General System Malfunctions107
Sender/Receiver Unit108
Control Unit109
Specification111
Technical Data112
Dimensions, Part Nos113
Sender/Receiver Units113
Bracket for Sender/Receiver Unit115
MCU Control Unit116
Junction Box117
Accessories118
Accessories for Mounting118
Connection Cable, Sender/Receiver Unit - Junction Box118
Options118
MCU Control Unit118
Miscellaneous119
Consumable Parts for 2-Years Operation119
Password120

SICK FLOWSIC200 - Assembly and Installation

Table of Contents

Related product manuals