Smartrise F220

To Next Page

To Previous Page

HYDRO INSTALLATION

QUICK START MANUAL

Smartrise now sends a quick start manual inside the

controller cabinet. These manuals allow the technician

to get the controller running in Construction Mode. If

the manual for the controller is missing it can be

downloaded at:

http://www.smartrise.us/support/

Main Page

Controller Grounding Requirements5
Table of Contents6
General Information10
- Bypass Term Limits20
Hydro Installation22
- Main Power Setup23
- Motor Wiring - 3/9 Lead Motor Wiring24
- Motor Wiring - 6/12 Lead Motor Wiring25
- Valve Wiring26
- Soft Start Setup - Sprecher + Schuh27
- Soft Start Setup - Siemens31
Ac Traction Installation37
- Main Power Setup38
- Motor & Brake Wiring39
Encoder Wiring (Instructions Per Manufacturer Drive Type)40
- Magnetek Hpv900-S2 Drive47
  - Induction Motor Setup47
  - Permanent Magnet Setup52
- Magnetek L1000A Drive59
  - Induction Motor Setup59
  - Permanent Magnet Setup65
- Keb Drive72
  - Induction Motor Setup72
  - Pm Motor Setup81
Brake Board Adjusting & Replacing Procedure91
- Brake Board Replacement92
- Brake Board Adjustment93
Steel Tape Landing System97
- Ip8300 Selector, Tape and Magnets98
- Door Zone Magnet Installation - Tape101
- Ut1/Dt1 Magnet Description - Tape106
- Ut1/Dt1 Magnet Alignment - Tape107
- Uet/Det Magnet Placement - Tape108
  - Hoistway Switch Positioning Table - Nts109
Tapeless Landing System110
- Governor Encoder Landing System Installation114
- Uet/Det Magnet Placement - Rail122
- Nts Magnet Placement - Rail123
Slide Distance Determination Procedure for Ets Magnet Placement124
MANUAL ETS and FINAL LIMIT SWITCHES131
- Final Switch Placement - Tape132
- Final Switch Placement - Rail133
Smoke Sensors, Shunt, & Load Weighing134
- Smoke Sensor Setup135
  - Smoke Sensor Setup Illustration - Lower Level Machine Room139
- Shunt Operation140
- Load Weighing141
Emergency Power & Safety String142
- Emergency Power143
- Safety String Description144
  - Safety String Troubleshooting144
Door Operator General145
Installation145
- Movfr Door Operator146
  - Movfr Door Operator - G.a.l. Certified Phe147
- Ipc Door Operator Control Model D3000148
- Adjusting Door Dwell Times153
Battery Lowering Device154
Reynolds & Reynolds Battery Lowering Device - "BLD155
- BLD / MOVFR Door Operator Voltage Issues157
Learning the Hoistway158
Adjusting Car Speeds162
- Car Speed Profiles Overview163
Adjusting Floor Levels167
- Adjustment too High/Too Low Method168
- Adjusting Up/Down Stop Points Method170
Testing Procedures for Hydro Controllers173
- Emergency Power Testing174
- Normal Limit Testing Setup175
- Normal / NTS Stopping Test176
- ETS Slowdown Test177
- Normal/Directional Limits Test178
- Re-Leveling with In-Car Stop Switch (Hydraulic System)178
- Redundancy Test179
- Battery Lowering Test179
- Buffer Test180
- Stop Ring Test - Low Speed181
- Low Oil / Low Pressure Test181
- Leveling Speed Test (V2.35E or Newer Only)182
- Leveling Zone Test182
- Pressure Test (Hydraulic System)183
- Hydro Rupture Setup183
Testing Procedures for Traction Controllers184
- Normal Limit Testing Setup185
- Nts Switch Drive Setup186
- Nts Switch Position Setup190
- Nts Switch Testing Procedure192
- Emergency Terminal Stopping Device (Ets)192
- Normal/Directional Limits194
- Redundancy Test195
- Manual Brake Release Test195
- Battery Lowering Test195
- Buffer Test196
- Pressure Test (Hydraulic System)197
- Re-Leveling with In-Car Stop Switch (Hydraulic System)197
- Stop Ring Test - Low Speed198
- Overspeed and Governor Test - Magnetek Drive199
- Overspeed and Governor Test - L1000A200
- Earthquake Counterweight Test202
- Leveling Zone Test202
- Unintended Movement203
- Rack and Pinion Drop Test204
- LOSS of TRACTION TEST (2010 Code Compliance Only)205
Other Adjustments206
- Access Top/Bottom Limits206
- Position Indicator Via Ce206
- Resynching - Hydros206
- Simplex Parking Setup206
- Hydro Rupture Setup206
Smartrise Menu Definitions207
Faults & Alarms215
- Common Fault Clearing Procedures218
Alarm Description Index250
Sru Input / Output Programming Tutorial254
Appendix A - Smartrise Boards257
Appendix B - Making Cat5 Cables259
Appendix C - Replacing Relays260
Addendum I - Replacing and Programming Adefective Sru Board263
Addendum II - Encoder Wiring Tables270
Addendum III - Traction Brake Pick Operation271
Addendum IV - Parameter Adjustments272
Addendum V - Security275
Addendum VI - Screen Lockout Feature277
Addendum VII - Pi Conversion Table278

Table of Contents

Related product manuals