Smartrise F220 - Magnetek Hpv900-S2 Drive; Induction Motor Setup

279 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

46

MAGNETEK HPV900-S2

DRIVE

INDUCTION MOTOR SETUP

Table of Contents

Controller Grounding Requirements5
Table of Contents6
General Information10
- Bypass Term Limits20
Hydro Installation22
- Main Power Setup23
- Motor Wiring - 3/9 Lead Motor Wiring24
- Motor Wiring - 6/12 Lead Motor Wiring25
- Valve Wiring26
- Soft Start Setup - Sprecher + Schuh27
- Soft Start Setup - Siemens31
Ac Traction Installation37
- Main Power Setup38
- Motor & Brake Wiring39
Encoder Wiring (Instructions Per Manufacturer Drive Type)40
- Magnetek Hpv900-S2 Drive47
  - Induction Motor Setup47
  - Permanent Magnet Setup52
- Magnetek L1000A Drive59
  - Induction Motor Setup59
  - Permanent Magnet Setup65
- Keb Drive72
  - Induction Motor Setup72
  - Pm Motor Setup81
Brake Board Adjusting & Replacing Procedure91
- Brake Board Replacement92
- Brake Board Adjustment93
Steel Tape Landing System97
- Ip8300 Selector, Tape and Magnets98
- Door Zone Magnet Installation - Tape101
- Ut1/Dt1 Magnet Description - Tape106
- Ut1/Dt1 Magnet Alignment - Tape107
- Uet/Det Magnet Placement - Tape108
  - Hoistway Switch Positioning Table - Nts109
Tapeless Landing System110
- Governor Encoder Landing System Installation114
- Uet/Det Magnet Placement - Rail122
- Nts Magnet Placement - Rail123
Slide Distance Determination Procedure for Ets Magnet Placement124
MANUAL ETS and FINAL LIMIT SWITCHES131
- Final Switch Placement - Tape132
- Final Switch Placement - Rail133
Smoke Sensors, Shunt, & Load Weighing134
- Smoke Sensor Setup135
  - Smoke Sensor Setup Illustration - Lower Level Machine Room139
- Shunt Operation140
- Load Weighing141
Emergency Power & Safety String142
- Emergency Power143
- Safety String Description144
  - Safety String Troubleshooting144
Door Operator General145
Installation145
- Movfr Door Operator146
  - Movfr Door Operator - G.a.l. Certified Phe147
- Ipc Door Operator Control Model D3000148
- Adjusting Door Dwell Times153
Battery Lowering Device154
Reynolds & Reynolds Battery Lowering Device - "BLD155
- BLD / MOVFR Door Operator Voltage Issues157
Learning the Hoistway158
Adjusting Car Speeds162
- Car Speed Profiles Overview163
Adjusting Floor Levels167
- Adjustment too High/Too Low Method168
- Adjusting Up/Down Stop Points Method170
Testing Procedures for Hydro Controllers173
- Emergency Power Testing174
- Normal Limit Testing Setup175
- Normal / NTS Stopping Test176
- ETS Slowdown Test177
- Normal/Directional Limits Test178
- Re-Leveling with In-Car Stop Switch (Hydraulic System)178
- Redundancy Test179
- Battery Lowering Test179
- Buffer Test180
- Stop Ring Test - Low Speed181
- Low Oil / Low Pressure Test181
- Leveling Speed Test (V2.35E or Newer Only)182
- Leveling Zone Test182
- Pressure Test (Hydraulic System)183
- Hydro Rupture Setup183
Testing Procedures for Traction Controllers184
- Normal Limit Testing Setup185
- Nts Switch Drive Setup186
- Nts Switch Position Setup190
- Nts Switch Testing Procedure192
- Emergency Terminal Stopping Device (Ets)192
- Normal/Directional Limits194
- Redundancy Test195
- Manual Brake Release Test195
- Battery Lowering Test195
- Buffer Test196
- Pressure Test (Hydraulic System)197
- Re-Leveling with In-Car Stop Switch (Hydraulic System)197
- Stop Ring Test - Low Speed198
- Overspeed and Governor Test - Magnetek Drive199
- Overspeed and Governor Test - L1000A200
- Earthquake Counterweight Test202
- Leveling Zone Test202
- Unintended Movement203
- Rack and Pinion Drop Test204
- LOSS of TRACTION TEST (2010 Code Compliance Only)205
Other Adjustments206
- Access Top/Bottom Limits206
- Position Indicator Via Ce206
- Resynching - Hydros206
- Simplex Parking Setup206
- Hydro Rupture Setup206
Smartrise Menu Definitions207
Faults & Alarms215
- Common Fault Clearing Procedures218
Alarm Description Index250
Sru Input / Output Programming Tutorial254
Appendix A - Smartrise Boards257
Appendix B - Making Cat5 Cables259
Appendix C - Replacing Relays260
Addendum I - Replacing and Programming Adefective Sru Board263
Addendum II - Encoder Wiring Tables270
Addendum III - Traction Brake Pick Operation271
Addendum IV - Parameter Adjustments272
Addendum V - Security275
Addendum VI - Screen Lockout Feature277
Addendum VII - Pi Conversion Table278

Related product manuals

Preview: Smartrise SRU

Smartrise HYDRO:EVOLVED

Smartrise HPV900