Topcon ES-101 - 10.5 Connecting via Communication Cable

324 pages

Save Page as PDF

To Next Page

To Previous Page

10. CONNECTING TO EXTERNAL DEVICES

PROCEDURE Basic cable settings

1. Connect the ES to the external

device using the cable.

Cables: "36.2 Optional

accessories"

2. Select “Comms setup” in Config

mode.

Set communication conditions.

"33.1 Configuration -Config

Mode-"

10.5 Connecting via Communication Cable

Main Page

Default Chapter6
- Table of Contents6
1 Precautions for Safe Operation11
2 Precautions15
3 Laser Safety Information20
4 Functions22
- Parts of the Instrument22
- Mode Diagram26
- Bluetooth Wireless Technology27
5 Basic Operation29
- Basic Key Operation29
- Display Functions32
- Star Key Mode35
6 Using the Battery36
- Battery Charging36
- Installing/Removing the Battery38
7 Setting up the Instrument39
- Centering39
- Levelling41
8 Focussing and Target Sighting44
9 Power On/Off46
10 Connecting to External Devices48
- Necessary Settings for Bluetooth Communication48
- Establishing a Connection between the es50
  - And Paired Bluetooth Device53
- Measurement Using Bluetooth Communication56
- Registering/Outputting Data Using Bluetooth Communication57
- Connecting Via Communication Cable59
11 Angle Measurement60
- Measuring the Horizontal Angle between Two Points60
  - (Horizontal Angle 0°)60
- Setting the Horizontal Angle to a Required Value61
  - (Horizontal Angle Hold)61
- Angle Measurement and Outputting the Data63
12 Distance Measurement64
- Returned Signal Checking65
- Distance and Angle Measurement66
- Recalling the Measured Data67
- Distance Measurement and Outputting the Data68
- Coordinate Measurement and Outputting the Data69
- REM Measurement71
13 Setting Instrument Station74
- Entering Instrument Station Data and Azimuth Angle75
- Setting Instrument Station Coordinate with Resection Measurement82
14 Coordinate Measurement95
15 Setting-Out Measurement98
- Coordinates Setting-Out Measurement99
- Distance Setting-Out Measurement102
- REM Setting-Out Measurement105
16 Setting-Out Line107
- Defining Baseline107
- Setting-Out Line Point112
- Setting-Out Line Line115
17 Setting-Out Arc118
- Defining an Arc118
- Setting-Out Arc125
18 Point Projection129
- Defining Baseline129
- Point Projection130
19 Topography Observation132
- Observation Setting133
- Observation136
20 Offset Measurement140
- Single-Distance Offset Measurement140
- Angle Offset Measurement142
- Two-Distance Offset Measurement144
- Plane Offset Measurement147
- Column Offset Measurement149
21 Missing Line Measurement151
- Measuring the Distance between 2 or more Points151
- Changing the Starting Point156
22 Surface Area Calculation158
23 Intersections162
24 Traverse Adjustment166
25 Route Surveying175
- Instrument Station Settings175
- Straight Line Calculation177
- Circular Curve Calculation179
- Spiral Curve182
- Parabola188
- Point Calculation192
- Intersection Angle/Azimuth Angle Calculation195
- Route Calculation197
26 Cross Section Survey212
27 Point to Line MEASUREMENT218
28 Recording Data - Topo Menu221
- Recording Instrument Station Data221
- Recording Backsight Point223
- Recording Angle Measurement Data226
- Recording Distance Measurement Data227
- Recording Coordinate Data228
- Recording Distance and Coordinate Data230
- Recording Notes231
- Reviewing JOB Data232
- Deleting Recorded JOB Data234
29 Selecting/Deleting a Job236
- Selecting a JOB236
- Deleting a JOB239
30 Registering/Deleting Data240
- Registering/Deleting Known Point Data240
- Reviewing Known Point Data244
- Registering/Deleting Codes245
- Reviewing Codes247
31 Outputting Job Data248
- Outputting JOB Data to Host Computer248
32 Using Usb Memory Device252
- Inserting the USB Memory Device253
- Storing JOB Data to USB Memory Device254
- Selecting T Type/S Type254
- Loading Data in USB Memory Device to the es257
- Displaying and Editing Files259
- Formatting the Selected External Memory Media260
33 Changing the Settings262
- Configuration -Config Mode262
- EDM Settings269
- Allocating Key Functions274
- Restoring Default Settings278
- Changing Password278
34 Warning and Error Messages280
35 Checks and Adjustments285
- Circular Level285
- Tilt Sensor286
- Collimation289
- Reticle290
- Optical Plummet292
- Additive Distance Constant294
- Laser Plummet296
36 Standard Equipment and Optional Accessories300
- Standard Equipment300
- Optional Accessories300
- Prism System302
- Power Supplies303
37 Specifications305
38 Explanation312
- Manually Indexing the Vertical Circle by Face Left, Face Right Measurement312
- Correction for Refraction and Earth Curvature314
39 Regulations315

Topcon ES-101 - 10.5 Connecting via Communication Cable

Table of Contents

Related product manuals