Parameter List
11
11.10 H: Terminal Functions
YASKAWA SIEPC71061737D GA800 Drive Technical Reference 605
Setting Value Function Description Ref.
139 !Watt Hour Pulse Output
Outputs the pulse that shows the watt hours.
929
13C !LOCAL Control
Selected
The terminal deactivates when the Run command source or frequency reference source is LOCAL.
ON : REMOTE
OFF : LOCAL
929
13D !During Speed Search
The terminal deactivates when the drive does speed search.
929
13E !PID Feedback Low
The terminal deactivates when the drive detects FbL [PID Feedback Loss].
929
13F !PID Feedback High
The terminal deactivates when the drive detects FbH [Excessive PID Feedback].
929
14A !During KEB Ride-Thru
The terminal deactivates when the drive executes the KEB Ride-Thru function.
929
14B !During Short Circuit
Braking
The terminal deactivates during Short Circuit Braking.
Note:
When A1-02 = 8 [Control Method Selection = EZ Vector Control], this function is available when you use a PM
motor.
929
14C !During Fast Stop
The terminal deactivates when the fast stop is in operation.
929
14D !oH Pre-Alarm Reduction
Limit
The terminal deactivates when L8-03 = 4 [Overheat Pre-Alarm Selection = Operate at Reduced Speed (L8-19)] and
oH [Heatsink Overheat] does not clear after the drive decreases the frequency for 10 cycles.
929
14E !Braking Transistor Fault
(rr)
The terminal deactivates when the internal braking transistor overheats and the drive detects an rr [Dynamic Braking
Transistor Fault] fault.
929
14F !Braking Resistor
Overheat (rH)
The terminal deactivates when the braking resistor overheats and the drive detects an rH [Braking Resistor Overheat]
fault.
929
160 !Internal Cooling Fan
Failure
The terminal deactivates when the drive detects a cooling fan failure in the drive.
929
161 !RotorPositionDetection
Complete
The terminal deactivates when drive receives a Run command and the drive detects the motor magnetic pole position
of the PM motor.
929
162 !Modbus Reg 1 Status
Satisfied
The terminal deactivates when the bit specified by H2-07 turns on regarding the MEMOBUS register address
configured with H2-08.
929
163 !Modbus Reg 2 Status
Satisfied
The terminal deactivates when the bit specified by H2-10 turns on regarding the MEMOBUS register address
configured with H2-09.
929
165 !Standby Output
The terminal activated after the drive stops operating and after the time set with b8-51 [Standby Mode Wait Time].
ON : The Run command turns off and the drive stops operating. When time set in b8-51 [Standby Mode Wait Time] is
expired, the magnetic contactor on the input side turns off.
OFF : The Run command turns on and the magnetic contactor on the input side turns on.
929
166 !Comparator 1
The terminal deactivates when the monitor value set with H2-20 is within range of H2-21 and H2-22 for the time set in
H2-24.
929
167 !Comparator 2
The terminal deactivates when the when the monitor value set with H2-26 is outside the range of H2-27 and H2-28 for
the time set in H2-30.
929
169 !External Power 24V
Supply
The terminal deactivates when there is an external 24V power supply between terminals PS-AC.
ON : The external 24V power supply is not supplying power.
OFF : The external 24V power supply is supplying power.
929
16A !Data Logger Error
The terminal deactivates when the drive detects a LoG [Com Error / Abnormal SD card].
929
190 !DWEZ Digital Output 1
Sets the DriveWorksEZ digital output 1. Refer to the DriveWorksEZ online manual for more information.
929
To Next Page
Loading...
