ABB DCS550 - Page 185

185
Signal and parameter list
3ADW000379R0501 DCS550 Manual e e
Signal / Parameter name
min.
max.
def.
unit
10.11 - 10.14 Unused
10.15 OnOff1 (On/Off1 command)
Binary signal for
OnOff1, UsedMCW (7.04) bit 0:
0 =
NotUsed
1 =
DI1 On by rising edge (0 → 1), 0 = Off1
2 =
DI2 On by rising edge (0 → 1), 0 = Off1
3 =
DI3 On by rising edge (0 → 1), 0 = Off1
4 =
DI4 On by rising edge (0 → 1), 0 = Off1
5 =
DI5 On by rising edge (0 → 1), 0 = Off1
6 =
DI6 On by rising edge (0 → 1), 0 = Off1
7 =
DI7 On by rising edge (0 → 1), 0 = Off1, default
8 =
DI8 On by rising edge (0 → 1), 0 = Off1
9 =
DI9 On by rising edge (0 → 1), 0 = Off1, only available with digital extension board
10 =
DI10 On by rising edge (0 → 1), 0 = Off1, only available with digital extension board
11 =
DI11 On by rising edge (0 → 1), 0 = Off1, only available with digital extension board
12 =
MCW Bit11 On by rising edge (0 → 1), 0 = Off1, MainCtrlWord (7.01) bit 11
13 =
MCW Bit12 On by rising edge (0 → 1), 0 = Off1, MainCtrlWord (7.01) bit 12
14 =
MCW Bit13 On by rising edge (0 → 1), 0 = Off1, MainCtrlWord (7.01) bit 13
15 =
MCW Bit14 On by rising edge (0 → 1), 0 = Off1, MainCtrlWord (7.01) bit 14
16 =
MCW Bit15 On by rising edge (0 → 1), 0 = Off1, MainCtrlWord (7.01) bit 15
17
-20 = reserved
21 =
DI7DI8 On and Start by rising edge (0 → 1) of DI7, Stop and Off1 by falling edge (1 → 0) of
DI8. Following settings apply: OnOff1 (10.15) = StartStop (10.16) = DI7DI8.
Note:
To give
On and Run at the same time set OnOff1 (10.15) = StartStop (10.16).
Int. Scaling: 1 == 1 Type: C Volatile: N
NotUsed
DI7DI8
DI7
-
10.16 StartStop (Start/Stop command)
Binary signal for
StartStop, UsedMCW (7.04) bit 3:
0 =
NotUsed
1 =
DI1 Start by rising edge (0 → 1), 0 = Stop
2 =
DI2 Start by rising edge (0 → 1), 0 = Stop
3 =
DI3 Start by rising edge (0 → 1), 0 = Stop
4 =
DI4 Start by rising edge (0 → 1), 0 = Stop
5 =
DI5 Start by rising edge (0 → 1), 0 = Stop
6 =
DI6 Start by rising edge (0 → 1), 0 = Stop
7 =
DI7 Start by rising edge (0 → 1), 0 = Stop
8 =
DI8 Start by rising edge (0 → 1), 0 = Stop, default
9 =
DI9 Start by rising edge (0 → 1), 0 = Stop, only available with digital extension board
10 =
DI10 Start by rising edge (0 → 1), 0 = Stop, only available with digital extension board
11 =
DI11 Start by rising edge (0 → 1), 0 = Stop, only available with digital extension board
12 =
MCW Bit11 Start by rising edge (0 → 1), 0 = Stop, MainCtrlWord (7.01) bit 11
13 =
MCW Bit12 Start by rising edge (0 → 1), 0 = Stop, MainCtrlWord (7.01) bit 12
14 =
MCW Bit13 Start by rising edge (0 → 1), 0 = Stop, MainCtrlWord (7.01) bit 13
15 =
MCW Bit14 Start by rising edge (0 → 1), 0 = Stop, MainCtrlWord (7.01) bit 14
16 =
MCW Bit15 Start by rising edge (0 → 1), 0 = Stop, MainCtrlWord (7.01) bit 15
17
-20 = reserved
21 =
DI7DI8 On and Start by rising pulse (0 → 1) of DI7, Stop and Off1 by falling pulse (1 → 0) of
DI8. Following settings apply: OnOff1 (10.15) = StartStop (10.16) = DI7DI8.
Note:
To give
On and Run at the same time set OnOff1 (10.15) = StartStop (10.16).
Int. Scaling: 1 == 1 Type: C Volatile: N
NotUsed
DI7DI8
DI8
-