ABB DCS550 - Page 268

268
Signal and parameter list
3ADW000379R0501 DCS550 Manual e e
Signal / Parameter name
min.
max.
def.
unit
99.07 ApplRestore (application restore)
Setting
ApplRestore (99.07) = Yes
starts the loading / storing of the macro (preset parameter set) selected by
means of
ApplMacro (99.08). ApplRestore (99.07) is automatically set back to Done after the chosen action
is
finished:
0 =
Done no action or macro change completed, default
1 =
Yes macro selected with ApplMacro (99.08) will be loaded into the drive
Notes:
−
Macro changes are only accepted in Off state [MainStatWord (8.01) bit 1 = 0].
−
It takes about 2 s, until the new parameter values are active.
Int. Scaling: 1 == 1 Type: C Volatile: Y
Done
Yes
Done
-
99.08 ApplMacro (application macro)
ApplMacro (99.08)
selects the macro (preset parameter sets) to be loaded / stored into the RAM and flash. In
addition to the preset macros, two user
-defined macros (User1 and User2) are available.
The operation selected by
ApplMacro (99.08) is started immediately by setting ApplRestore (99.07) = Yes.
ApplMacro (99.08)
is automatically set back to NotUsed after the chosen action is finished. The selected
macro is shown in
MacroSel (8.10):
0 =
NotUsed default
1 =
Factory load macro factory (default parameter set) into RAM and flash - User1 and User2
will not be influenced
2 =
User1Load load macro User1 into RAM and flash
3 =
User1Save save actual parameter set form RAM into macro User1
4 =
User2Load load macro User2 into RAM and flash
5 =
User2Save save actual parameter set form RAM into macro User2
6 =
Standard load macro standard into RAM and flash
7 =
Man/Const load macro manual / constant speed into RAM and flash
8 =
Hand/Auto load macro hand (manual) / automatic into RAM and flash
9 =
Hand/MotPot load macro hand (manual) / motor potentiometer into RAM and flash
10 =
reserved
11 =
MotPot load macro motor potentiometer into RAM and flash
12 =
TorqCtrl load macro torque control into RAM and flash
13 =
TorqLimit load macro torque limit into RAM and flash
14 =
DemoStandard load macro demo standard into RAM and flash
15 =
2WreDCcontUS load macro 2 wire with US style DC-breaker into RAM and flash
16 =
3WreDCcontUS load macro 3 wire with US style DC-breaker into RAM and flash
17 =
3WreStandard load macro 3 wire standard into RAM and flash
Notes:
−
When loading a macro, group 99 is set / reset as well.
−
If User1 is active, AuxStatWord (8.02) bit 3 is set. If User2 is active, AuxStatWord (8.02) bit 4 is set.
−
It is possible to change all preset parameters of a loaded macro. On a macro change or an application
restore command of the actual macro the ma
cro depending parameters are restored to the macro’s default
values.
−
In case macro User1 or User2 is loaded by means of ParChange (10.10),
it is not saved into the flash and
thus not valid after the next power on.
Int. Scaling: 1 == 1 Type: C Volatile: Y
NotUsed
TorqCtrl
NotUsed
-
99.09 DeviceName (device name)
DeviceName (99.09)
is fixed set to DCS550 and cannot be changed.
Note:
This parameter is only visible if a SDCS
-COM-8 is connected.
Int. Scaling: 1 == 1 Type: C Volatile: N
DCS550
DCS550
DCS550
-
99.10 NomMainsVolt (nominal AC mains voltage)
Nominal mains voltage (AC) of the supply. The default and maximum values are preset automatically
according to
TypeCode (97.01).
Absolute max. is 525 V
Int. Scaling: 1 == 1 V Type: I Volatile: N
0
(97.01)
(97.01)
V
99.11 M1NomFldCur (nominal field current)
Nominal field current from the motor rating plate.
Int. Scaling: 100 == 1 A Type: I Volatile: N
0.3
35
0.3
A