Agilent Technologies 8712ET - Page 318

Index
Programmer’s Guide Index-11
reference impedance
specifying
, 11-45
reference marker
amplitude
, 11-10
frequency
, 11-10
reference oscillator
, 11-52
reference position
, 6-27
reference value
, 6-27
referenced name does not exist
,
13-14
reflection port
, 11-37
register
service request enable
, 9-18
register model
status
, 5-3
register sets
, 5-10, 5-11
register summary bit
, 5-3
registers
, 5-2
how to use
, 5-6
remote enable
, 1-12
control line
, 1-5
Remote IP Addr/Host key
,11-61,
11-62
Remove Automount key
, 11-61
REN
, 1-5, 1-12
rename a file
, 11-32
reporting of events
, 5-5
request service
, 5-13
Request Service bit
, 1-13
reset device
, 9-18
resistance
marker query
, 11-11
resolution
display frequency
, 11-20
hardcopy
, 11-29
resolution, data values
, 6-9
response to query
, 9-11
reversed byte order
, 4-7
RF in port
, 11-37
RF out port
, 11-37
RFWD
, 6-22
RGB color map
, 11-23
RL1
, 1-8
ROUTe
, 9-4, 11-37
RPG
, 8-2
RQS
, 1-12, 1-13
RQS bit
, 5-7
S
saturation
, 11-23
save instrument state
, 11-32
SAVE RECALL hardkey (ES/
ET)
, 10-55
scale and offset
, 6-27
scale calculations
, 6-27
SCALE hardkey (ES/ET)
, 10-60
SCORR1
, 6-23
SCPI
1996.0 standard
, 12-3, 12-10
command reference
, 11-4
commands
, 8-2
conformance
, 12-2
defined
, 9-2
errors
, 13-2
introduction to
, 9-2
standard commands
, 12-3
syntax conventions
, 9-14
SCPI commands
menu association
, 10-2
screen format
, 11-23
SDC
, 1-12, 1-15
search
marker
, 11-10
seconds display
, 11-20
select
active IBASIC program
, 11-36
ASCII data format
, 11-33
detection mode
, 11-47
hardcopy port
, 11-28
mass storage device
, 11-32
program
, 11-35, 11-36
Selected Device Clear
, 1-12
selected device clear
, 1-12
self calibration
automatic
, 11-12
enable periodic, 11-12
initiation
, 11-12
SelfCal
, 11-12
self-test
, 9-5, 9-18
semantic error
, 5-22
semicolons
use of
, 9-7, 9-15
sending commands
, 1-6
SENSe
, 9-5, 11-38–11-51
sequential command
, 2-2
defined
, 2-2
example
, 2-9
serial number query
, 11-17
serial poll
, 1-12, 5-9
serial poll disable
, 1-13
serial port
, 11-18, 11-19
service request
, 5-6, 5-7
control line
, 1-5
enable register
, 9-18
generating
, 5-8
method of accessing registers
,
5-7
setting lost due to rtl
, 13-9
setting the stop frequency
, 9-10
settings conflict
, 13-10
SH1
, 1-8
short form
of commands
, 9-8
short form mnemonic
, 4-3
SICL
, 6-5
significant digits, number of
, 6-9
simcal command
, 11-68
single quotes
use of
, 9-13
size
trace data transfer
, 6-8
smith chart
, 6-4
Socket Port No. key
, 11-62
softkey
menus
, 10-2
More Cal
, 10-26
softkey labels
user-defined
, 11-22