Agilent Technologies 8712ET - Page 319

Index-12 Programmer’s Guide
Index
softkey menu labels,11-23
softkey press
sensing
,5-15
softkeys
SCPI commands
,10-2
SOURce
,9-5
source
set start frequency
,11-48
set stop frequency
,11-48
spaces
use of
,9-10,9-15
span
frequency for RF source
,11-48
s-parameters
measurement
,11-51
selecting
,11-51
SPD
,1-13
SPE
,1-12
SPOLL
,5-14
spur avoid
selection
,11-17
SR1
,1-8
SRE. See *SRE
SRE?. See *SRE?
SRL impedance
,6-26
SRQ
,1-5,5-6,5-7
SRQ line
,5-7
SRQ process
,5-9
SSTOP (start/stop)
,11-20
STANdard
,11-42
Standard Commands for
Programmable Instruments
(SCPI)
,9-2
standard event status
,5-10
enable register
,5-22
register
,5-3,9-16
register set
,5-20
summary
,5-13
start distance
cable fault location
,11-47
start frequency
set for RF source
,11-48
start value
frequency annotation
,11-21
state
recall
,11-31
statistic mean
,11-6
statistic peak-to-peak
,11-6
STATus
,9-5
PRESet command
,5-25
PRESet Settings
,5-25
status
firmware
,5-4
hardware
,5-4
Status Byte
,1-12
status byte
,5-2,5-8,5-10,9-18
clearing
,9-16
status byte register
,5-3,5-12
status port
,11-19
status register model
,5-3
status registers
,5-2
STB?. See *STB?
stop distance
cable fault location
,11-47
stop frequency
frequency annotation
,11-21
how to set
,9-10
set for RF source
,11-48
storing
calibration information
,11-44
frequency values
,11-33
instrument state
,11-32
trace values
,11-33
STRING
,11-3
string data
,4-4
string data error
,13-6
string data not allowed
,13-6
string parameters
,9-13
string variable
loading a new value
,11-36
string. See <string>.
structural return loss. See SRL.
subroutines
,6-2
built in
,6-10
high speed
,6-19
subsystems
,9-3
suffix
error
,13-5
not allowed
,13-5
too long
,13-5
units
,11-3,11-6,11-7,11-8,
11-10
user defined frequency
annotation
,11-21
SWAPped
,11-27
SWEep
,11-52
sweep
,11-30
set continuous/one-shot
,11-30
set time
,11-53
type
frequency
,11-34
power
,11-34
SWEEP hardkey (ES/ET)
,10-61
sweep time
enable/disable automatic
,11-
53
sweeps
how to take
,6-11
SWR
,6-26
synchronizing the analyzer
,2-2
syntax
conventions
,1-3
error
,5-22,13-3,13-4
summary and conventions
,9-
14
syntax conventions
,11-4
SYSTem
,9-5
PRESet command
,5-4
system controller
defined
,1-2
system impedance
,11-45
SYSTEM OPTIONS hardkey
(ES/ET)
,10-62
SYSTEM OPTIONS, Test Set
Cal Functions (ES/ET)
,10-
30