Alcatel-Lucent 7330 - Page 375

5 — VoIP overview
Alcatel-Lucent 7302 ISAM | 7330 ISAM FTTN | 7360 ISAM FX ONT R04.06.02 November 2013 5-29
3FE 55873 AAAA TCZZA Edition 01
ONT Product Information Guide
sip_dscp
(1)
The differentiated services code
point (DSCP) value that should
populate the DS field of SIP packets
sent by the user agent. It is an
integer value in the range of zero (0)
to 63. The default value is the value
configured via SNMP/TL1.
YYPackage
A, B, H,
I-240W-
S only
Yes, XML
takes
precedenc
e over TL1
or CLI.
TL1 using DSCP
using
ent-ontsip-config
C L I u s i n g d s c p
using
configure voice
ont sip-config
subscribe_p
eriod
(1)
The subscription expiration time that
the client will propose by including it
in an Expires header of a SUBSCRIBE
request. This is a non-negative
integer and the value is expressed in
seconds.The default value is 86400
(one day). (This parameter does not
apply to iConfig requests.)
NYPackage
A, B, H,
I-240W-
S only
Yes, TL1
and CLI
there is no
default
value
TL1 using
VOICEMAILTO
using
ed-ontvoiceportsi
p
CLI using
voice-mail-to
using
configure voice
ont voice-sip-port
subscribe_h
ead_start
(1)
The number of seconds prior to
expiration of a subscription at which
the client sends a SUBSCRIBE request
to refresh the subscription.This is a
non-negative integer and the value is
expressed in seconds. The default
value is 3600 (one hour).
NYPackage
A, B, H,
I-240W-
S only
No, value
is derived
from
FTP/defau
lt line
profile.
N/A
sip_timer_t1
(1)
The value of the SIP T1 timer (the
round-trip time estimate). This is a
non-negative integer and the value is
expressed in milliseconds. The range
is 1 to 65535. The default value is
500.
YYPackage
A, B, H,
I-240W-
S only
No, value
is derived
from
FTP/defau
lt line
profile.
N/A
sip_timer_t2
(1)
The value of the SIP T2 timer (the
maximum retry interval for a
non-INVITE request). This is an
integer and the value is expressed in
seconds. The range is 1 to 65535. The
default is 4.
YYPackage
A, B, H,
I-240W-
S only
No, value
is derived
from
FTP/defau
lt line
profile.
N/A
sip_invite_ti
meout
(1)
The INVITE transaction timeout,
designated as Timer B in RFC 3261.
This is an integer. The value is
expressed in seconds. The range is 1
to 65535. The default value is 32
(64*T1).
YYPackage
A, B, H,
I-240W-
S only
No, value
is derived
from
FTP/defau
lt line
profile.
N/A
sip_noninvit
e_timeout
(1
)
The non-INVITE transaction timeout,
designated as Timer F in RFC 3261.
This is an integer and the value is
expressed in seconds. The range is 1
to 65535. The default value is 32
(64*T1).
YYPackage
A, B, H,
I-240W-
S only
No, value
is derived
from
FTP/defau
lt line
profile.
N/A
default_pro
duct_id
Specifies the application server
product identifier that shall be
assumed for product-specific
communication with the application
server if the application server does
not provide a product identifier. The
value of this parameter is any string
that can be used as the value of a
server or user agent header. The
default is an empty string.
YYAll
except
package
C, D, E,
and
I-240W-
S ONTs
No, value
is derived
from
FTP/defau
lt line
profile.
N/A
Parameter Description Mode
1
Mode
2
Device OMCIv2
support?
TL1 and CLI
parameters
(4 of 7)