Why won't the engine starter run on my Andreoli Engineering Paint Sprayer?
T
travis83Aug 22, 2025
If the engine starter of your Andreoli Engineering Paint Sprayer doesn't run, there are several potential causes:
* The main joystick might not be in neutral position. Ensure it is.
* The red emergency button may be pressed. Release it.
* The safety switch on the hydrostatic pump could be damaged. Consider replacing it.
* A low battery charge could be the issue. Try replacing the battery.
* Oxidized battery connectors can prevent starting. Clean them.
* The starter or ignition block might be worn out or damaged, requiring replacement.
* A damaged safety switch in the seat may also be the reason. In this case, replace the switch.
E
Emma EdwardsSep 4, 2025
Why is the alternator lamp always on when the engine is running on my Andreoli Engineering ATOM 1000?
W
Wendy ParkSep 4, 2025
If the alternator lamp is always on when the engine runs on your Andreoli Engineering Paint Sprayer, it could indicate:
* A damaged drive belt. Replace the belt.
* A damaged alternator. Replace the alternator.
A
Ashley BerrySep 3, 2025
Why does the spray pressure decrease after some use with my Andreoli Engineering ATOM 1000 Paint Sprayer?
T
thomastaylorSep 3, 2025
If the spray pressure of your Andreoli Engineering Paint Sprayer decreases after a period of normal work, consider these possibilities:
* Pump valves may be worn out. Check and/or replace them.
* There might be dirt in the pump valves. Check and/or replace them.
* The pump could be sucking air. Inspect the suction hoses, suction filter, and pump suction manifold.
M
Melvin ChristensenSep 1, 2025
What should I do if the high coolant temperature lamp is on in my Andreoli Engineering ATOM 1000 Paint Sprayer?
M
Martin Baldwin DDSSep 1, 2025
If the high coolant temperature lamp is on in your Andreoli Engineering Paint Sprayer, it could be due to:
* A clogged cooler. Clean the cooler.
* Low coolant level. Refill the coolant.
* A worn-out coolant pump. Replace the pump.
K
Kayla McintyreAug 30, 2025
What causes low spray pressure even when the chemical pump is running normally on my Andreoli Engineering ATOM 1000 Paint Sprayer?
P
Paul RiddleAug 31, 2025
If the chemical pump on your Andreoli Engineering Paint Sprayer is running normally but the spray pressure is low, consider the following:
* The pump might be sucking air. Check the suction hoses, suction filter, and pump suction manifold.
* The valves may be worn out. Check, clean, and/or replace them.
* The seat of the pressure regulator valve might be damaged. Check and/or replace it.
* The pressure regulator could be blocked in the drain position. Check and/or replace it.
* The dump valve might be blocked in the open position. Check and/or replace it.
* The nozzle might not be correctly fitted or could be worn out. Check and/or replace it.
W
Walter PeckAug 29, 2025
Why is the pump on my Andreoli Engineering ATOM 1000 Paint Sprayer so noisy?
T
Thomas MccannAug 29, 2025
If your Andreoli Engineering Paint Sprayer's pump is noisy, consider the following potential causes:
* Air suction: Check suction hoses, suction filter, and pump suction manifold.
* Broken or worn out springs of pump valves: Replace the springs.
* Presence of dirt in pump valves: Check and clean the valves.
* Worn out bearings: Replace the bearings.
* Excessive temperature of the mixture: Cool the mixture.
L
Linda WoodwardAug 27, 2025
Why won't the chemical pump start on my Andreoli Engineering Paint Sprayer?
E
ericosbornAug 28, 2025
If the chemicals pump of your Andreoli Engineering Paint Sprayer doesn't start, consider these potential causes:
* The engine revs might be too high. Slow down the revs below 1200 rpm.
* There could be a faulty electric connection. Check and restore the connection.
* The electric clutch might be faulty, requiring a check and potential replacement.
* There might be a problem in the gearbox, requiring a check and potential replacement.
* A problem in the driving cardan shaft may exist, requiring a check and potential replacement.
* A problem in the drive belt could be the cause, requiring a check and potential replacement.
A
April GlennAug 27, 2025
How to fix high coolant temperature in Andreoli Engineering ATOM 1000?
F
Frederick WelchAug 27, 2025
If your Andreoli Engineering Paint Sprayer is experiencing high coolant temperature, here are a few things to check:
* The cooler might be clogged. Clean it.
* The cooler fan might not be running. Check the drive belt.
* The coolant level could be low. Refill the coolant expansion tank.
J
Jennifer HughesAug 25, 2025
Why is there no electric power to my Andreoli Engineering ATOM 1000 Paint Sprayer?
T
Timothy VillaAug 25, 2025
If there is no electric power in your Andreoli Engineering Paint Sprayer, check the following:
* The main fuse might be damaged; check and replace if necessary.
* The battery may be low; replace the battery.
* Battery connections could be oxidized; clean the connections.
* The battery main switch might be open; close the main switch.
K
Kevin JonesAug 23, 2025
What to do if the starter runs but the engine won't start on my Andreoli Engineering ATOM 1000 Paint Sprayer?
J
Jane OwensAug 23, 2025
If the starter runs but the engine of your Andreoli Engineering Paint Sprayer doesn't start, consider the following:
* The battery charge might be low, requiring a battery replacement.
* Fuel filters could be obstructed, needing a check and replacement if necessary.
* There might be difficulty sucking fuel; try using the fuel manual pump.
* Injectors could be blocked, requiring inspection and potential replacement.
* The fuel level might be low. Refill the fuel tank.
To Next Page
General