Anilam Wizard 900

To Next Page

To Previous Page

168

EDM Features (900E Only) (Continued)

For Example: The DRO is in EDM Mode and the axis displays indicate the following:

i.4i5

Remaining distance to Target

Depth

. 5.200

Desired Z-Depth

z 3.785

Actual position relative to the zero

position

Main Page

Table of Contents3
Contents4
Introducing the Wizard7
The ANILAM Wizard 450/450L Keypad and Display Windows8
The ANILAM Wizard 450/450L Back Panel9
First-Time User Checklist11
About this Manual13
Function Code List14
Beeper OFF/ON - F 2117
Keyboard Entry Error18
Inch/Metric Conversion19
Decimal Degree to Degree-Minutes-Seconds Conversion20
Plus/Minus (±) Key21
Absolute/Incremental (ABS/INCR) Key22
Presetting a Dimension23
Recalling a Preset Dimension24
Clearing a Preset Dimension25
Resetting an Axis to Zero26
Axis Reset Only - F 1627
Absolute Zero Set - F 0129
Absolute Zero Set at Reference Mark - F 9030
Evertrack TM Mode - F 0231
Last Position Save/Recall - F 10/F 1136
Adding/Subtracting Values37
Dividing an Axis Value by 238
Centering Key39
Radius/Diameter Per Axis - F 0541
Setting a Correction Factor - F 0343
100-Point Axis Error Compensation - F 80/F 8145
Measure the Axis45
Selecting the Compensation Table, Entering an Axis Compensation47
Key Functions for Compensation Table50
Deleting a Compensation Value Table51
Axis Error Compensation ON/OFF52
Correction Factor OFF/ON - F 0453
Approaching Zero Indicator54
Approaching Zero - F 0655
Approaching Zero Range - F 0757
Approaching Zero Audio ON/OFF - F 0859
Connecting the Edge Sensor Probe60
Edge Sensor Probe - F 0961
Feedrate ON/OFF - F 2663
Job Clock ON/OFF - F 3464
Parameter Settings - F 2066
Setting up Encoder Parameters66
Metric Linear Encoders68
Inch Linear Encoders (BT or JB Linear Encoders)72
Rotary Encoders73
Display DIM OFF/ON - F 22/ F 2377
Axis Designation - F 2478
Select Language - F 9979
Linear Encoder Error Detect OFF/ON - F 40/F 4180
Diagnostics - F 4581
Advanced (ADV) Functions Key84
Help Function84
Bolt-Hole Pattern Function (450 Only)86
Partial Bolt-Hole Pattern88
Full Bolt-Hole Pattern (450 Only)92
Recalling Bolt-Hole Pattern Function (450 Only)96
Linear-Hole/Frame-Hole Pattern Function (450 Only)99
Recalling Linear-Hole/Frame-Hole Function (450 Only)104
Taper Calculator Function (450L Only)107
Enter Datum114
Enter Datum (Alternate Method)117
Recall Datum119
Clear Datum - F 31120
Enter Tool Offset121
Recall Tool Offset123
Modify Tool Offset - F 35124
Clear Tool Offset - F 32125
Output Connections (with I/O Option Only)143
Input Connections (with I/O Option Only)144
Zero Output ON/OFF (with I/O Option Only) - F 33145
Zero Output Time Select (with I/O Option Only) - F 25147
Interface (with I/O Option Only)148
Setup (with I/O Option Only) - F 27149
ON/OFF (with I/O Option Only) - F 28152
Printing Axis Values (with I/O Option Only)153
Remote Operation (with I/O Option Only)154

Anilam Wizard 900 - Page 174

Table of Contents

Related product manuals