Cisco ASR 5000 Series

To Next Page

To Previous Page

RMA Shipping Procedures

▀ Packaging ASR 5000 Cards

▄ ASR 5000 Installation Guide

312

Packaging a Half-height Line Card

The packaging sequence is as follows:

Step 1 Place the card inside the ESD bag; fold over and seal the bag with an ESD Label or tape as shown in the photos.

Main Page

Default Chapter3
- Table of Contents3
About this Guide11
- Conventions Used12
- Dimensions12
- Related Documentation13
- Contacting Customer Support13
ASR 5000 Hardware Platform Overview15
- The ASR 5000 Platform16
- Chassis Configurations17
- Chassis Description21
- Power Filter Units26
- Fan Tray Assemblies27
- Application Cards29
- Line Cards35
- Card Interlock Switch51
- Card Identifiers52
Installation Procedure Overview55
- Chassis Components56
- Installation at a Glance58
- Required Tools and Equipment59
  - Hand Tools59
  - Equipment59
- Site Prerequisites60
- Protecting against Electro-Static Discharge61
- Federal Communications Commission Warning63
  - ICS Notice63
  - Laser Notice63
Chassis Installation65
- Equipment Rack Configuration66
  - Ventilation Considerations66
  - Mounting Options68
- Weight Considerations68
- Unpacking the ASR 5000 Chassis69
- Installing the Chassis71
Application Card Installation83
- Chassis Slot Numbering and Assignments84
- Installing Application Cards87
Line Card Installation91
- Chassis Slot Numbering and Assignments92
- Line Card Redundancy95
  - Side-By-Side Redundancy for the XGLC95
    - Requirement Summary95
    - CLI Commands for XGLC Redundancy96
- Recommended Minimum Chassis Configuration97
- Installing Half-Height Line Cards98
- Installing the 10 Gigabit Ethernet Line Card (XGLC)101
  - Preparing a Full-Height Line Card Slot101
  - Installing the XGLC101
Cabling the Switch Processor Input/Output Line Card105
- SPIO Interfaces106
  - E1 BNC BITS Interface Version107
  - T1 3-Pin BITS Interface Version108
- Connecting to the Management LAN109
  - Using the SFP Interfaces109
  - Using the Ethernet RJ-45 Interfaces111
- Connecting to the Serial Console Port113
- Connecting to a BITS Timing Source117
- Connecting to the CO Alarm Interface119
  - Electrical Characteristics121
  - Central Office Alarm Wiring Example121
Cabling the Fast Ethernet (10/100) Line Card123
- FLC2 Interfaces124
Cabling the Gigabit Ethernet Line Cards127
- Gigabit Ethernet Line Card (GLC2)128
- Quad Gigabit Ethernet Line Card (QGLC)130
- RJ-45 SFP Module Detail132
- Cabling the Optical SFP Interface133
- Gigabit Ethernet Line Card (XGLC)134
- Cabling the Optical SFP+ Interface136
Cabling the Optical (ATM) Line Cards137
- Optical (ATM) Line Card Interfaces138
- Cabling the Optical SFP Interface140
Cabling the Channelized Line Cards141
- Channelized Line Card Interfaces142
- Cabling the Optical SFP Interface144
Cabling the Power Filter Units145
- Power Considerations146
  - Estimating Power Requirements146
  - Power Cable Requirements147
- Connecting the PFU to the Power Source150
Applying Power and Verifying the Installation153
- Understanding the System Boot Process154
- Applying Power to the Chassis156
- Verifying the Installation158
- Completing Initial System Configuration185
System Monitoring187
- Monitoring188
  - Daily - Standard Health Check188
  - Periodic Status Checks190
- Counters and Bulkstats191
- Summary of Maintenance Tasks192
Adding Application and Line Cards to an Existing Installation195
- Chassis Slot Numbering and Assignments196
- Adding Application Cards197
- Adding Half-Height Line Cards200
- Adding a 10 Gigabit Ethernet Line Card203
  - Preparing a Full-Height Line Card Slot203
  - Installing the XGLC203
Removing and Installing SMC PC Cards207
- Installing PC Cards208
- Removing PC Cards210
Replacing the Chassis Air Filter213
- Determining When an Air Filter Needs Replacing214
- Removing the Air Filter215
- Installing the Air Filter217
Replacing a Power Filter Unit219
- Determining that a PFU Has Failed220
- Removing the Failed PFU221
- Installing the Replacement PFU224
- What to Do with the Failed PFU227
Replacing Upper or Lower Fan Tray229
- Determining Whether a Fan Tray Needs Replacing230
  - Using the CLI230
  - Using SNMP Traps and MIB Objects230
- Removing an Upper Fan Tray232
- Installing an Upper Fan Tray234
- Removing a Lower Fan Tray Assembly235
- Installing a Lower Fan Tray Assembly237
- What to Do with the Failed Fan Tray238
Replacing Application Cards239
- Determining Whether an Application Card Has Failed240
  - Using the CLI240
  - Using SNMP Traps241
- Removing the Application Card242
- Installing the Application Card244
- Replacing the CF Memory Card on Smcs246
  - Replacing the Compactflash on an SMC247
- What to Do with the Failed Application Card248
Replacing Line Cards249
- Determining Whether a Line Card Has Failed250
  - Using the CLI250
  - Using SNMP Traps251
- Removing the Line Card252
- Installing the Line Card254
- What to Do with the Failed Line Card256
Technical Specifications257
- Physical Dimensions258
- Weights259
- Power Specifications260
  - Estimating Power Requirements260
- Mounting Requirements261
- Interface Specifications263
Safety, Electrical and EMC Certifications277
- Federal Communications Commission Warning278
  - ICS Notice278
  - Laser Notice278
- Safety Certifications278
- Electrical Certifications279
- Environmental Certifications279
- Acoustic Noise279
- Electromagnetic Compatibility (EMC) Compliance280
  - Japan VCCI-A280
  - Korean EMC280
Environmental Specifications281
- Operating and Storage Parameters282
- Supported Environmental Standards282
- Chassis Air Flow283
Hardware Product Support Matrix285
- Packet Processing Cards286
- Line Cards288
Preparing a Full-Height Line Card Slot291
- Introduction292
- Remove Blanking Panels293
- Remove the Half-Height Card Guide294
Rohs Compliance Statement299
- Chassis300
- Fan Assembly301
- Power Filter Unit (PFU)302
- Full Product303
RMA Shipping Procedures305
- RMA Overview306
- Packaging ASR 5000 Cards308

Table of Contents

Other manuals for Cisco ASR 5000 Series

Related product manuals