Claas LEXION 480 - Page 4

0.1.2 RHB LEXION 480 - 188 678.1
Contents
3. Threshing mechanism
Feed rake conveyor ............................................................... 3.1.1
Removing the feed rake conveyor ................................... 3.1.1
Installing the feed rake conveyor ..................................... 3.1.3
Removing the intercepting piece ..................................... 3.1.4
Installing the intercepting piece ....................................... 3.1.4
Removing the feed rake conveyor
suction blower .................................................................. 3.1.5
Disassembling the feed rake conveyor
suction blower .................................................................. 3.1.5
Feed rake conveyor suction blower,
disassembled ................................................................... 3.1.7
Assembling the feed rake conveyor
suction blower .................................................................. 3.1.8
Installing the feed rake conveyor
suction blower .................................................................. 3.1.9
Removing the top feed rake shaft .................................... 3.1.9
Feed rake top shaft, disassembled ................................ 3.1.14
Installing the feed rake top shaft .................................... 3.1.15
Removing the bottom feed rake roller ............................ 3.1.19
Bottom feed rake roller, disassembled .......................... 3.1.21
Assembling the bottom feed rake roller ......................... 3.1.21
Installing the bottom feed rake roller .............................. 3.1.21
Replacing the wooden ledges ........................................ 3.1.22
Removing the intermediate floor .................................... 3.1.23
Installing the intermediate floor ...................................... 3.1.25
Replacing the runners .................................................... 3.1.25
Removing the intermediate drive shaft .......................... 3.1.26
Intermediate drive shaft, disassembled ......................... 3.1.30
Installing the intermediate drive shaft ............................ 3.1.31
Removing the reverser drive .......................................... 3.1.32
Reverser drive, disassembled ....................................... 3.1.34
Installing the reverser drive ............................................ 3.1.35
Replacing the feeder chains .......................................... 3.1.35
Threshing concave ................................................................. 3.2.1
Removing the stone trap .................................................. 3.2.1
Installing the stone trap .................................................... 3.2.1
Removing the preconcave ............................................... 3.2.2
Preconcave, disassembled .............................................. 3.2.5
Installing the preconcave ................................................. 3.2.6
Removing the main concave ........................................... 3.2.7
Main concave, disassembled ......................................... 3.2.10
Installing the main concave ........................................... 3.2.12
Basic concave setting .................................................... 3.2.16
Adjusting the concave potentiometer ............................. 3.2.21
Learning the limit stops .................................................. 3.2.21
Learning the limit stops .................................................. 3.2.22
Accelerator ............................................................................. 3.3.1
Removing the bearing assembly and
the shaft on the right-hand side ....................................... 3.3.1
Disassembling the right-hand bearing assembly ............. 3.3.3
Assembling the right-hand bearing .................................. 3.3.3
Installing the right-hand bearing assembly
and shaft .......................................................................... 3.3.5
Removing the bearing assembly
on the left-hand side ........................................................ 3.3.8
Disassembling the left-hand bearing assembly ............. 3.3.10
Assembling the left-hand bearing assembly .................. 3.3.11
Installing the left-hand bearing assembly ...................... 3.3.12
Replacing the accelerator caps ..................................... 3.3.13
Removing the accelerator ............................................. 3.3.14
Accelerator, disassembled ............................................ 3.3.17
Installing the accelerator ............................................... 3.3.18
Threshing drum ..................................................................... 3.4.1
Removing the right-hand drum bearing assembly ........... 3.4.1
Disassembling the right-hand drum bearing .................... 3.4.3
Right-hand drum bearing, disassembled ......................... 3.4.4
Installing the right-hand drum bearing ............................. 3.4.5
Removing the left-hand drum bearing assembly ............. 3.4.6
Disassembling the left-hand drum bearing ...................... 3.4.8
Left-hand drum bearing assembly,
disassembled .................................................................. 3.4.8
Installing the left-hand drum bearing assembly ............... 3.4.9
Removing the threshing drum ....................................... 3.4.10
Threshing drum, disassembled ..................................... 3.4.12
Renewing the beater bars ............................................. 3.4.13
Removing the threshing drum shaft .............................. 3.4.14
Installing the threshing drum shaft ................................ 3.4.16
Installing the threshing drum ......................................... 3.4.17
Impeller .................................................................................. 3.5.1
Removing the right-hand impeller bearing ...................... 3.5.1
Installing the right-hand impeller bearing ........................ 3.5.3
Removing the left-hand impeller bearing ......................... 3.5.3
Installing the left-hand impeller bearing ........................... 3.5.5
Removing the impeller ..................................................... 3.5.6
Installing the impeller ....................................................... 3.5.8
Removing the flanged shaft
(from serial no. ...) ........................................................... 3.5.9
Impeller disassembled
(from serial no. ...) ......................................................... 3.5.10
Installing the flanged shaft ............................................. 3.5.11
Removing the impeller shaft
(up to serial no. ...) ........................................................ 3.5.12
Impeller disassembled
(up to serial no. ...) ........................................................ 3.5.13
Installing the impeller shaft
(up to serial no. ...) ........................................................ 3.5.14
Axial rotors ............................................................................. 3.6.1
Removing the separation grates ..................................... 3.6.1
Installing the separation grates ....................................... 3.6.3
Removing the separating jacket ...................................... 3.6.3
Installing the separating jacket ........................................ 3.6.6
Removing the axial rotor supporting arm ........................ 3.6.7
Disassembling the axial rotor supporting arm ................. 3.6.8
Supporting arm, disassembled ........................................ 3.6.9
Installing the axial rotor supporting arm .......................... 3.6.9
Removing the axial rotor ............................................... 3.6.11
Installing the axial rotor ................................................. 3.6.13
Removing the hybrid unit completely ............................ 3.6.14
Installing the hybrid unit ................................................. 3.6.22
4. Cleaning unit
Return pan ............................................................................. 4.1.1
Lowering the return pan
(from serial no. ...) ........................................................... 4.1.1
Raising and installing the return pan
(from serial no. ...) ........................................................... 4.1.2