0.1.4 RHB LEXION 480 - 188 678.1
Contents
Lower grain tank unloading angle drive,
disassembled
(from serial no. …) ........................................................... 5.3.18
Assembling the lower grain tank
unloading angle drive
(from serial no. ...) .......................................................... 5.3.19
Installing the lower grain tank
unloading angle drive
(from serial no. ...) .......................................................... 5.3.22
Removing the lower grain tank
unloading angle drive
(up to serial no. ...) ......................................................... 5.3.23
Disassembling the lower grain tank
unloading angle drive
(up to serial no. ...) ......................................................... 5.3.24
Lower grain tank unloading angle drive,
disassembled
(up to serial no. …) ........................................................... 5.3.27
Assembling the lower grain tank
unloading angle drive
(up to serial no. ...) ......................................................... 5.3.28
Installing the lower grain tank
unloading angle drive
(up to serial no. ...) ......................................................... 5.3.31
Removing the upper grain tank
unloading angle drive ..................................................... 5.3.32
Disassembling the upper grain tank
unloading angle drive ..................................................... 5.3.33
Upper grain tank unloading angle drive,
disassembled ................................................................. 5.3.34
Assembling the upper grain tank
unloading angle drive ..................................................... 5.3.35
Installing the upper grain tank
unloading angle drive ..................................................... 5.3.38
Removing the grain tank unloading tube ....................... 5.3.39
Refitting the unloading auger tube ................................. 5.3.40
Removing the grain tank unloading tube elbow ............. 5.3.40
Installing the grain tank unloading tube elbow ............... 5.3.41
Removing the vertical unloading auger tube ................. 5.3.41
Installing the vertical unloading auger tube ................... 5.3.42
6. Straw discharge
Straw chopper ........................................................................ 6.1.1
Removing the right-hand straw chopper bearing ............. 6.1.1
Right-hand straw chopper bearing assembly,
disassembled ................................................................... 6.1.3
Installing the right-hand straw chopper bearing ............... 6.1.3
Removing the left-hand straw chopper bearing ............... 6.1.5
Left-hand straw chopper bearing assembly,
disassembled ................................................................... 6.1.6
Installing the left-hand straw chopper bearing ................. 6.1.6
Removing the cutting cylinder .......................................... 6.1.7
Cutting cylinder, disassembled ...................................... 6.1.11
Installing the cutting cylinder .......................................... 6.1.12
Replacing the free-swinging knives ............................... 6.1.13
Uni-spreader .......................................................................... 6.2.1
Removing the fan blade bearings .................................... 6.2.1
Assembling and installing the fan blade bearing ............. 6.2.8
7. Drives
Drive belts .............................................................................. 7.1.1
General Information ......................................................... 7.1.1
Drive diagram ........................................................................ 7.1.2
Drive diagram, left-hand .................................................. 7.1.2
Drive system diagram, right-hand side ............................ 7.1.3
Left-hand drive belts .............................................................. 7.2.1
Removing the cutterbar drive belt (1)
(Cutterbar drive without variable-speed drive) ................ 7.2.1
Installing and adjusting the cutterbar drive belt (1)
(Cutterbar drive without variable-speed drive) ................ 7.2.2
Removing the cutterbar drive belt (2)
(Cutterbar drive with variable-speed drive) ..................... 7.2.3
Installing and adjusting the cutterbar drive belt (2)
(Cutterbar drive with variable-speed drive) ..................... 7.2.4
Removing the cutterbar variable-speed
drive belt (3) .................................................................... 7.2.5
Installing and adjusting the cutterbar
variable-speed drive belt (3) ............................................ 7.2.6
Removing the impeller drive belt (4) ................................ 7.2.7
Installing and adjusting the impeller drive
belt (4) ............................................................................. 7.2.8
Removing the cutterbar intermediate drive belt (5) ......... 7.2.9
Installing and adjusting the cutterbar
intermediate drive belt (5) .............................................. 7.2.10
Removing the uni-spreader hydraulic pump
drive belt (6) .................................................................. 7.2.11
Installing and adjusting the uni-spreader
hydraulic pump drive belt (6) ......................................... 7.2.11
Removing the main intermediate drive belt (7) .............. 7.2.12
Installing and adjusting the main
intermediate drive belt (7) .............................................. 7.2.14
Removing the grain tank unloading
intermediate drive belt (8) .............................................. 7.2.16
Installing and adjusting the grain tank
unloading intermediate drive belt (8) ............................. 7.2.17
Removing the straw chopper
intermediate drive belt (9) .............................................. 7.2.18
Installing and adjusting the straw chopper
intermediate drive belt (9) .............................................. 7.2.19
Removing the straw chopper drive
belts (10 and 11) ........................................................... 7.2.20
Installing and adjusting the straw chopper
drive belts (10 and 11) ................................................... 7.2.22
Removing the uni-spreader
intermediate drive belt (12) ............................................ 7.2.23
Installing and adjusting the uni-spreader
intermediate drive belt (12) ............................................ 7.2.24
Removing the sieve pan intermediate
drive belt (13) ................................................................ 7.2.25
Installing and adjusting the sieve pan
intermediate drive belt (13) ............................................ 7.2.26
Removing the sieve pan intermediate
drive belt (14) ................................................................ 7.2.27
Installing and adjusting the sieve pan
intermediate drive belt (14) ............................................ 7.2.28
Removing the sieve pan drive belt (15) ......................... 7.2.29
To Next Page
