SECTION : 5C
CLUTCH
CAUTION : Disconnect the negative battery cable before removing or installing any electrical unit or when a tool
or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help
prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise noted.
TABLE OF CONTENTS
SPECIFICATIONS 5C0–1. . . . . . . . . . . . . . . . . . . . . . . . .
FASTENER TIGHTENING
SPECIFICATIONS 5C0–1. . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS 5C0–2. . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS TABLE 5C0–2. . . . . . . . . . . . . . . . . .
DIAGNOSIS 5C0–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH OPERATION 5C0–2. . . . . . . . . . . . . . . . . . . .
COMPONENT LOCATOR 5C0–4. . . . . . . . . . . . . . . . . . .
HYDRAULIC CLUTCH COMPONENTS 5C0–4. . . . .
MAINTENANCE AND REPAIR 5C0–7. . . . . . . . . . . . . .
ON–VEHICLE SERVICE 5C0–7. . . . . . . . . . . . . . . . . . . .
CLUTCH PEDAL 5C0–7. . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH PEDAL POSITION SWITCH 5C0–9. . . . . . .
CLUTCH DISC AND RELATED
COMPONENTS 5C0–10. . . . . . . . . . . . . . . . . . . . . . .
CLUTCH PEDAL
ADJUSTMENT (HYDRAULIC) 5C0–15. . . . . . . . . . .
CLUTCH RELEASE POINT
ADJUSTMENT (HYDRAULIC) 5C0–17. . . . . . . . . . .
AIR BLEEDING 5C0–17. . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH MASTER
CYLINDER ASSEMBLY 5C0–17. . . . . . . . . . . . . . . .
CLUTCH RELEASE
CYLINDER ASSEMBLY 5C0–20. . . . . . . . . . . . . . . .
UNIT REPAIR 5C0–21. . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH MASTER CYLINDER 5C0–21. . . . . . . . . . . .
CLUTCH RELEASE CYLINDER 5C0–23. . . . . . . . . . .
GENERAL DESCRIPTION AND
SYSTEM OPERATION 5C0–25. . . . . . . . . . . . . . . . . . .
DRIVING MEMBERS 5C0–25. . . . . . . . . . . . . . . . . . . .
DRIVEN MEMBERS 5C0–25. . . . . . . . . . . . . . . . . . . . .
OPERATING MEMBERS 5C0–25. . . . . . . . . . . . . . . . .
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application NSm Lb–Ft Lb–In
Clutch Fork–to–Release Lever Shaft Bolt 35 26
Clutch Master Cylinder Locknuts 22 18
Clutch Pedal Nut 18 13
Pressure Plate–to–Flywheel Bolt 15 11
Release Bearing Guide Sleeve Bolts 5 45
Release Cylinder Bolts 60 44
To Next Page
Loading...
