Delfin LYRA - Compressed Air Treatment Group (Optional)

154 pages

Save Page as PDF

To Next Page

To Previous Page

Pag 55 / 154

Manuale Lyra 600 sx elettr eng

4.3 Compressed air treatment group (optional)

Reference fig. 4.3.1.

1. Exclusion air supply valve and pressure relief.

2. Filter.

3. Pressure regulator.

4. Manometer.

Fig. 4.3.1 Compressed air treatment group

Main Page

Default Chapter2
- Table of Contents2
General Information7
- List of Documents7
- This Instruction Manual7
- Information Property8
- Meanings and Symbols9
- Identification Data of the Manufacturer9
- Machine Identification Data10
- EC Conformity Declaration10
- Warranty11
- Technical Assistance12
- Use of the Manual12
Operators' Safety and Protective Devices14
- Safety Requirements14
- Classification of Machine Operators14
- Machine Work Zones17
- Description of the Command/Control and Work Stations19
- Designed Use and Prohibited Use21
- Protective Devices, Signs and PPE24
- Residual Risks34
- General Instructions for Safety and Prevention45
Technical Data48
Installation50
- Positioning and Levelling of the Machine50
- Electrical Connection54
- Compressed Air Treatment Group (Optional)55
Controls57
- Touch Screen Control Panel57
Film Roll Holder Shaft and Calander Assembly60
- General Instructions60
- Description of the Components61
- Reel Assembly and Disassembly62
- Film Dragging Device63
- Automatic Film Junction64
- Film Editing67
Fin Wheel Assembly's Pulling/Sealing Set70
- General Instructions70
- Description of the Components71
- Adjustment of the Fin Wheel Pressure72
- Replacement of a Resistance/Probe73
- Adjustments of the Motorized Reel (Optional)75
Transverse Sealing Jaw Assembly77
- General Instructions77
- Jaw Teeth Adjustments78
- Jaw Teeth Adjustment on a Sealing Jaw with Longitudinal Sealing Pattern79
- Jaw Teeth Adjustment on a Sealing Jaw with Transverse Sealing Pattern83
- Assembly and Adjustment of the Knife86
- Replacement of the Brushes on the Slip Ring Holders87
- Heat Adjustment and Replacement of the Heaters88
Torque Limit (Safety Clutch) on the Sealing Jaws (Only for Mechanical Torque Limiter)91
Bag Length Adjustment with Neutral Film (Not Film Registered Film), on an Electronic Machine94
Setting to Work the Photocell Group96
Adjustment of the Bag Length with Print Registered Film (Optional)98
Infeed Conveyor101
- General Instructions101
- Pusher Dismantling and Assembly103
- Pusher Support Dismantling and Assembly104
- Adjustment of the Infeed Conveyor Side Guides105
- Infeed Conveyor Chain Tensioning106
Forming Box Adjustments108
- General Instructions108
- Fixed Forming Box109
- Adjustable Forming Box109
- Fixed Adjustable Forming Box113
Discharge Belt Conveyor116
- General Instructions116
- Maintenance117
Use and Maintenance of Machinery120
- Checking Efficiency Protection Devices120
- Use and Maintenance121
- Scheduled Maintenance122
- Replacement of Sealing Jaw Supply Wires123
- Check of Belts/Chain Conditions and Tension124
- Periodically Lubrication125
Packaging Problems and Solutions128
Touch Screen Panel131
- Home Page133
- Alarm134
- Alarm135
- Temperature Control Page136
- Block Notes - Setting137
- Block Notes - Setting138
- Block Notes Page139
- Product Counter Page140
- Photocell for Print-Registered Film Page (Optional)141
- 20.10 Product Phase Page142
- 20.11 Transversal Sealing Unit Slowdown Page143
- Printing Unit Page (Optional)144
- No Product no Bag Page (Optional)145
- Automatic Film Junction (Optional)146
- Gusseting Page (Optional)147
- 20.16 Manual Mode Page148
- Outfeed Conveyor Page (Optional)149
- 20.18 Electronic Clutch Limiter Page150
- Recipes Page151
- 20.31 List of Recipes Page152
Attached List of Documents154

Delfin LYRA - Compressed Air Treatment Group (Optional)

Table of Contents