ECKELMANN VS 300 - Page 158

ECKELMANN VS 300

172 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Parameter List and Menu Structure of VS 300

150

Doku-Version 2.05 - Firmware 2.10 - 15. September 2017

Notice:

Table of Contents

Table of Contents3
Conventions9
Warning Signs and Symbols Employed10
- Safety Instructions11
- Disclaimer in the Event of Non-Compliance12
- Intended Use13
- Electrostatic Sensitive Devices (Esds)14
- System Design of VS 30015
- New Features Compared to Earlier Versions17
- Application of VS 30019
- System Expansion Options20
- Function of VS 30023
- Dispatching of the Internal Alarm Outputs24
- Example of VS 300 System Configuration25
- Configuration / Monitoring of Digital Inputs27
- Low-Pressure Control / Compressor Control29
- Setting Parameters for LP Transducer Characteristic30
- Control Algorithm with Low-Pressure Control31
- Control Algorithm with Speed Controller33
- Determining the Setpoint with Speed Controller35
- Control Algorithm with Combined Controller36
- Loading and Unloading Fixed-Speed Compressors38
Determining the Low-Pressure Setpoint40
Second Setpoint – Setpoint Increase/Decrease41
Humidity Shift42
Booster-/Satellite Operation43
Demand-Dependent Calculation of Setpoint45
Response to Fault Conditions46
Disabling Refrigeration Points47
Forced Shutdown of Compressors / Oil Equalization48
Load Shedding50
- High Pressure Monitoring51
- Low Pressure Monitoring52
- Compressor Starts Monitoring53
- Monitoring the Digital Inputs54
- Setting HP Transducer Characteristic55
- Control Algorithm for High-Pressure Control56
- Control Algorithm with Speed Control57
- Determining the Setpoint for Speed Control58
- Control Algorithm with Combined Controller59
- Loading and Unloading of Fixed-Speed Fans61
Determining the High-Pressure Setpoint62
Second Setpoint - Setpoint Increase / Decrease64
Relay / Control Stage Actuating Mode65
- First Start66
- Daily Run Times67
- Compressor Pack Activity / Utilization68
- Connection and Safety Notes69
- Installation70
- Startup71
First Start – Loading Default Settings72
Setting the CAN Bus Address74
Setting the Current Date and Time75
Other Parameters to be Set76
- Battery Replacement77
- Updating the Firmware78
- Pin and Terminal Assignments of VS 30083
- View of Connecting Terminals84
- Pin Assignments and Their Function85
- Operation of VS 30087
- Controls89
- First Start – Loading Default Values90
- Parameter Setting – General91
- Selecting Parameter Lists92
- Changing the Access Level93
- Setting the Current Date and Time (Parameter List S2)94
- Parameter Groups95
- Setting Parameters for the Week Timer (Parameter List T)96
- Manual Control / Service Mode (Parameter List C)97
- Operation System Centre / Store Computer / Operator Terminal99
- Remote Control Via a Terminal100
Menus and Operating Screens101
Calling the Controller Menu Via Remote Control103
System Centre CI 4X00104
Deactivating the Input Lock-Down105
Activating Service Mode106
- Parameter List and Menu Structure of VS 300107
- Parameter List A: Actual Values System Data108
- Parameter List S1: Overview of Main Setpoints - Day/Night Operation109
- Parameter List S2: Setpoints Basic Parameters - Night Operation110
- Parameter List S2: Setpoints Basic Parameters - Day/Night Operation111
- Parameter List S2: Common Setpoints113
- Parameter List S3: Common Setpoints System Configuration115
Parameter List S3: Basic Settings System Configuration116
Parameter List S4: Setpoints Alarm Priorities117
Parameter List S5: Suction Pressure Shift / Additional Parameters118
Parameter List T: Setpoints Timers119
Parameter List C: Service / Check Mode - Defaults Relay Outputs120
Parameter List F: Alarms - System and Process Fault Reports121
- Overview of Alarm Types123
- Menu Structure of al 300 Operator Terminal and CI 3000 Store Computer124
- Menu Structure125
- Menu 0 Main Menu128
- Menu 3 Setpoints130
- Menu 4 Clock146
- Menu 5 Alarms147
- Menu 7 Basic Settings156
- Decommissioning and Disposal159
- Alarms and Messages of VS 300161
- Messages / Alarms in the VS 300162
- Messages / Alarms al 300 Operator Terminal or CI 3000 Store Computer164
- System Fault Reports165
- Specifications of VS 300167
- Mechanical Data169
- Order No.'s and Accessories of VS 300171

Related product manuals

ECKELMANN VS 3000

Preview: ECKELMANN UA 300 D

ECKELMANN UA 300 D

Preview: ECKELMANN UA 412 S

ECKELMANN UA 412 S

Preview: ECKELMANN UA 400

ECKELMANN UA 400