Index
EST3 Installation and Service Manual Z.3
I
input circuits
delayed egress application • 3.20
description • 3.5
dummy loads • 3.23
elevator control application • 3.23
emergency exit door application • 3.24, 3.25
intermittent locks • 3.37
internal fault • 8.63
IRC-3 upgrade • 5.41
J
jumper settings
AC power source • 3.41
continuous locks • 3.36
DC power supply • 3.44
intermittent locks • 3.38
remote power supply • 3.44
jumpers • 3.8
K
keypads
description • 3.6
L
LEDs
dual LED control • 3.31, 3.48
length of SAC bus • 3.3
lobbies • 3.16
Local mercantile premises • C.3
lock circuit dummy loads
elevator control application • 3.23
muster station • 3.34
lock types
intermittent locks • 3.38
locks
CRC output • 3.7
CRCRL and external power supply • 3.4
logged anti-passback • 3.11
M
maglock peripherals application • 3.28
maglocks
code requirements • 3.28
CRC output • 3.7
delayed egress application • 3.19
magnetic stripe access cards • 3.6
maintenance philosophy • 8.3
manual audio zone selection • 1.38
mapping errors • 8.47, 8.52
message counters
Signature • 8.57
messages • 1.39
alarm format • 1.39
alert format • 1.40
automatic • 1.14
default • 1.14
modem transmission • 3.7
motion detectors • 3.5
multiple card readers application • 3.30
multiple tenants • 3.16
muster
3-RS232 card • 3.34
partitions • 3.34
report • 3.32
timed anti-passback • 3.11
muster application • 3.32
muster station
requirements • 3.32, 3.34
N
N.C. contacts • 3.6
N.O. contacts • 3.6
NAC circuit calculations • B.11
NAC synchronization • 5.6
network
applications and design considerations • 1.29
layout • 1.29
network data riser
cable properties • B.3
length • B.3
limits • B.2
specifications • B.2
wire capacitance • B.4
NFPA 101
delayed egress • 3.18
emergency exit door • 3.24
NFPA standards • C.2
notification zones • 5.8
O
open fault • 8.64
output circuits • 3.6
P
page channel • 1.35
page to alert • 1.35
page to evac • 1.35
pager messages • 3.3
panel controller • 8.9
partitions
muster application • 3.34
passive infrared motion detector • 3.28, 3.29
peripherals required for maglocks • 3.28
personality fault • 8.63
PIN schedules • 3.6
Police station connection • C.3
power
elevator control application • 3.23
transformer • 3.5
power for continuous locks application • 3.35
power for intermittent locks application • 3.37
power from a remote source application • 3.42
power from an AC source application • 3.39
power supplies
AC power source • 3.41
circuit common • 3.8, 3.23, 3.44, 3.46
continuous locks application • 3.36
DC power supply • 3.42, 3.44
elevator control application • 3.23
ground fault detection • 3.8
intermittent locks application • 3.38
jumper settings • 3.8
panel • 3.8
power from a remote source • 3.44
power from a remote source application • 3.42
power from an AC source application • 3.39
remote controls • 3.46
To Next Page
Loading...
Need help?
General