EasyManuals Logo

GE Corometrics 250cx Series User Manual

GE Corometrics 250cx Series
250 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #186 background imageLoading...
Page #186 background image
17-6 250cx Series Maternal/Fetal Monitor Revision C
2036946-001
Technical Specifications: Operating Modes
Maternal Blood Pressure Mode (DINAMAP
®
SuperSTAT)
Technique:
Blood Pressure Range:
Systolic
Diastolic Visual
Mean Arterial Pressure (MAP)
Pulse Rate Range:
Blood Pressure Accuracy:
Pulse Rate Accuracy:
Cuff Inflation:
Inflation Pressure Range:
Cuff Deflation:
Safety Features:
Display/Record:
Alarms:
Audio
Visual
Limits
Technical
Compliance:
Oscillometric. Microprocessor software eliminates most ambient noise
and motion artifact.
30–290 mmHg (4.0–38.7 kPa)
10–220 mmHg (1.3–29.3 kPa)
20–260 mmHg (2.7–34.7 kPa)
30–200 bpm
± 5 mmHg (0.7 kPa) with a standard deviation no greater than 8 mmHg
(1.1 kPa)
± 2 bpm or ± 2% (whichever is greater)
Initial inflation to 135 mmHg (18.0 kPa). Subsequent inflation
approximately 30 mmHg (4.0 kPa) greater than the previous systolic
pressure.
100-250 mmHg in increments of 5 (13.3 ± 33.3 kPa in steps of 0.7)
Automatic
Automatic cuff deflation if: cuff pressure exceeds the overpressure limit
of 315 mmHg ± 15 mmHg (42.0 ± 2.0 kPa); or maximum reading
determination time is exceeded (not to exceed AAMI /ANSI SP10-1992
limit of 180 s); or safety timer detects microprocessor failure. Auto
mode minimum 30-second delay from the end of one determination to
the beginning of another to allow for venous return.
Systolic, diastolic, and mean pressure; pulse rate
Alternating 1.5-second chimes
Flashing pressure numeric or message
User-selectable high and low systolic, diastolic, and mean pressures;
User-selectable high and low pulse rate
Cuff errors, connection errors, insufficient signal, excessive inflation or
determination times, overpressure, hose errors, excessive motion,
communication problem, or self-test failure.
The 250cx Series blood pressure parameter complies with the
American National Standard for Electronic or Automated
Sphygmomanometers [AAMI/ANSI SP10-1992]. The GE monitor
values are based on the oscillometric method of noninvasive blood
pressure measurement and correspond to comparisons with intra-aortic
values within ANSI/AAMI Standards for accuracy.
This device is covered under one or more of the following US Patents: 6,423,010; 6,358,213; 5,704,362; 5,680,870; 5,579,776; 5,518,000; 5,170,795; 5,052,397;
4,754,761; 4,638,810 and international equivalents. USA patents pending.
Operating Mode Specifications (Continued)

Table of Contents

Other manuals for GE Corometrics 250cx Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the GE Corometrics 250cx Series and is the answer not in the manual?

GE Corometrics 250cx Series Specifications

General IconGeneral
TypeFetal Monitor
Model250cx Series
ManufacturerGE Healthcare
Fetal Heart Rate MonitoringYes
Ultrasound Frequency1 MHz
Recorder Speed1, 2, 3 cm/min
Maternal ParametersECG, NIBP, SpO2
FHR Range30-240 bpm
TOCO Range0-100
ConnectivityRS-232
Power SourceAC Power
DisplayColor LCD

Related product manuals