Introduction
4/07 UDC2500 Universal Digital Controller Product Manual x
Table 4-26 Run/Monitor Functions ____________________________________________________ 123
Table 5-1 Voltage, Milliamp and Resistance Equivalents for Input 1 Range Values ______________ 137
Table 5-2 Voltage and Milliamp Equivalents for Input 2 Range Values ________________________ 139
Table 5-3 Equipment Needed_________________________________________________________ 139
Table 5-4 Set Up Wiring Procedure for Thermocouple Inputs Using an Ice Bath ________________ 140
Table 5-5 Set Up Wiring Procedure for Thermocouple Inputs using Thermocouple Source ________ 141
Table 5-6 Set Up Wiring Procedure for RTD Inputs _______________________________________ 141
Table 5-7 Set Up Wiring Procedure for Radiamatic, Millivolts, Volts or Thermocouple Differential Inputs
(Except 0-10 Volts) _____________________________________________________________
142
Table 5-8 Set Up Wiring Procedure for 0 to 10 Volts ______________________________________ 143
Table 5-9 Set Up Wiring Procedure for Milliampere Inputs _________________________________ 143
Table 5-10 Input 1 Calibration Procedure (Numeric Code 10000) ____________________________ 144
Table 5-11 Set Up Wiring Procedure for 0 to 20 mA or 4 to 20 mA Inputs – Input 2______________ 146
Table 5-12 Set Up Wiring Procedure for 0 to 2 Volts, 0 to 5 Volts, or 1 to 5 Volts – Input 2________ 147
Table 5-13 Input 2 Calibration Procedure (Numeric Code 20000) ____________________________ 148
Table 5-14 Restore Factory Calibration _________________________________________________ 149
Table 6-1 Set Up Wiring Procedure for Current Output ____________________________________ 152
Table 6-2 Current Output Calibration Procedure (Numeric Code 30000) ______________________ 153
Table 6-3 Set Up Wiring Procedure for Auxiliary Output___________________________________ 154
Table 6-4 Auxiliary Output Calibration Procedure (Numeric Code 50000) _____________________ 155
Table 6-5 Restore Factory Calibration Procedure _________________________________________ 156
Table 7-1 Procedure for Identifying the Software Version __________________________________ 160
Table 7-2 Procedure for Displaying the Status Test (Numeric Code 1200) Results _______________ 161
Table 7-3 Background Tests__________________________________________________________ 162
Table 7-4 Controller Failure Symptoms_________________________________________________ 164
Table 7-5 Troubleshooting Power Failure Symptoms ______________________________________ 166
Table 7-6 Troubleshooting Current Output Failure ________________________________________ 166
Table 7-7 Troubleshooting Three Position Step Control Output Failure________________________ 167
Table 7-8 Troubleshooting Time Proportional Output Failure _______________________________ 168
Table 7-9 Troubleshooting Current/Time or Time/Current Proportional Output Failure ___________ 169
Table 7-10 Troubleshooting Alarm Relay Output Failure ___________________________________ 170
Table 7-11 Troubleshooting a Keyboard Failure __________________________________________ 171
Table 7-12 Troubleshooting a RS-485 Communications Failure______________________________ 172
Table 7-13 Troubleshooting an Ethernet Communications Failure ____________________________ 173
Table 7-14 Troubleshooting Auxiliary Output Failure _____________________________________ 173
Table 7-15 Restoring Factory Configuration _____________________________________________ 174
Table 7-16 Software Upgrades________________________________________________________ 175
Table 8-1 Parts Identification_________________________________________________________ 178
Table 8-2 Parts Not Shown___________________________________________________________ 178
Table 8-3 Software Upgrades (see Section 7.9) ___________________________________________ 178
Table 9-1 Integer Parameter Type _____________________________________________________ 181
Table 9-2 Floating Point Parameter Type________________________________________________ 181
Table 9-3 Register Address Format for Function Code 20___________________________________ 183
Table 9-4 Register Address Format for Function Code 21___________________________________ 187
Table 10-1 Control Data Parameters ___________________________________________________ 191
Table 10-2 Option Status ____________________________________________________________ 191
Table 10-3 Miscellaneous Read Onlys__________________________________________________ 192
Table 10-4 SetPoint Program Read Only Information______________________________________ 192
Table 10-5 Setpoint Code Selections ___________________________________________________ 193
Table 10-6 Setpoint Associated Parameters______________________________________________ 193
To Next Page
Loading...
Need help?
General
