Honeywell UDC3200 User Manual

Table 5-1 Voltage, Milliamp and Resistance Equivalents for Input Range Values _______________ 133
Table 5-2 Equipment Needed_________________________________________________________ 135
Table 5-3 Set Up Wiring Procedure for Thermocouple Inputs Using an Ice Bath ________________ 136
Table 5-4 Set Up Wiring Procedure for Thermocouple Inputs using Thermocouple Source ________ 137
Table 5-5 Set Up Wiring Procedure for RTD Inputs _______________________________________ 137
Table 5-6 Set Up Wiring Procedure for Radiamatic, Millivolts, Volts or Thermocouple Differential Inputs
(Except 0-10 Volts) _____________________________________________________________ 138
Table 5-7 Set Up Wiring Procedure for 0 to 10 Volts ______________________________________ 139
Table 5-8 Set Up Wiring Procedure for Milliampere Inputs _________________________________ 139
Table 5-9 Input 1 or 2 Calibration Procedure _____________________________________________ 140
Table 5-10 Restore Factory Calibration _________________________________________________ 142
Table 6-1 Set Up Wiring Procedure for Current Output ____________________________________ 144
Table 6-2 Current Output Calibration Procedure __________________________________________ 145
Table 6-3 Set Up Wiring Procedure for Auxiliary Output ___________________________________ 146
Table 6-4 Auxiliary Output Calibration Procedure ________________________________________ 147
Table 6-5 Position Proportional and Three Position Step Output Calibration Procedure ___________ 148
Table 6-6 Restore Factory Calibration __________________________________________________ 151
Table 7-1 Procedure for Identifying the Software Version __________________________________ 155
Table 7-2 Procedure for Displaying the Status Test Results _________________________________ 156
Table 7-3 Background Tests__________________________________________________________ 157
Table 7-4 Controller Failure Symptoms_________________________________________________ 159
Table 7-5 Troubleshooting Power Failure Symptoms ______________________________________ 161
Table 7-6 Troubleshooting Current Output Failure ________________________________________ 161
Table 7-7 Troubleshooting Position Proportional Output Failure _____________________________ 162
Table 7-8 Troubleshooting Time Proportional Output Failure _______________________________ 163
Table 7-9 Troubleshooting Current/Time or Time/Current Proportional Output Failure ___________ 164
Table 7-10 Troubleshooting Alarm Relay Output Failure ___________________________________ 165
Table 7-11 Troubleshooting a Keyboard Failure __________________________________________ 166
Table 7-12 Troubleshooting a RS-485 Communications Failure______________________________ 167
Table 7-13 Troubleshooting an Ethernet Communications Failure ___________________________ 168
Table 7-14 Troubleshooting Auxiliary Output Failure _____________________________________ 169
Table 7-15 Restoring Factory Configuration _____________________________________________ 170
Table 7-16 Software Upgrades________________________________________________________ 171
Table 8-1 Parts Identification _________________________________________________________ 174
Table 8-2 Parts Not Shown___________________________________________________________ 174
Table 8-3 Software Upgrades (see Section 7.9) ___________________________________________ 174
Table 9-1 Integer Parameter Type _____________________________________________________ 177
Table 9-2 Floating Point Parameter Type________________________________________________ 177
Table 9-3 Register Address Format for Function Code 20___________________________________ 179
Table 9-4 Register Address Format for Function Code 21___________________________________ 183
Table 10-1 Control Data Parameters ___________________________________________________ 187
Table 10-2 Option Status ____________________________________________________________ 187
Table 10-3 Miscellaneous Read Onlys__________________________________________________ 188
Table 10-4 SetPoint Program Read Only Information ______________________________________ 188
Table 10-5 Setpoint Code Selections ___________________________________________________ 189
Table 10-6 Setpoint Associated Parameters ______________________________________________ 190
Table 10-7 Computer Setpoint Selection ________________________________________________ 190
Table 10-8 Computer Setpoint Associated Parameters _____________________________________ 191
Table 10-9 Set-up Group – Tuning ____________________________________________________ 192
Table 10-10 Set-up Group – Setpoint Ramp/Rate _________________________________________ 194
12/04 UDC3200 Universal Digital Controller Product Manual x

Honeywell UDC3200 Specifications

General

Brand	Honeywell
Model	UDC3200
Category	Controller
Language	English