What is the meaning of E11 error in hpmont HD5L-PLUS?
The E11 error code on the hpmont Controller suggests a CPU abnormality. You can try to detect at power up after completely power down. For other issues, seek technical support.
What does error code E10 mean on hpmont HD5L-PLUS Controller?
If your hpmont Controller is displaying error code E10, it indicates a circuit fault of braking unit, so seek technical support.
How to fix hpmont HD5L-PLUS Controller when there is no display when power up?
If there is no display when you power up the hpmont Controller, here are a few things to check: * First, verify the input power voltage. * Then, check the bus voltage to ensure the power supply of the drive board isn't faulty. * Also, make sure the wiring of the control board, drive board, and keypad is properly connected. Reconnect the keypad or check the wiring. If the rectifier bridge is damaged, contact the factory for repair. If the controller buffer resistance is damaged or the control board and keypad are faulty, further diagnosis is needed.
How to fix error E16 on hpmont HD5L-PLUS?
To address error E16 on the hpmont Controller, check the connection between HD5L-PLUS and the motor for output voltage phase disconnection or loss. Also, if the three-phase load of HD5L-PLUS is severely unbalanced, check the quality of motor.
What does E15 error mean on hpmont HD5L-PLUS?
If your hpmont Controller is showing error E15, it could indicate that, for a three-phase input HD5L-PLUS, an input phase loss fault has occurred to power input. Check the three-phase power input. For other issues, seek technical support.
How do I fix E18 error on hpmont HD5L-PLUS Controller?
To resolve the E18 error on your hpmont Controller, consider the following: * If there is a brake fault or contactor fault, change contactor. * If there is a PG pulse number fault, set proper PG P/R. * If there is an improper setting of F05.19, F05.20, correct the setting of F05.19 - F05.20. * If the controller torque is inadequate, select bigger capacity. * If the speed-loop PI parameter setting is incorrect, correctly set speed-loop PI parameter.
What to do if hpmont Controller displays E20 error?
If the hpmont Controller shows an E20 error, it could be related to the motor. The motor may be overheating, so reduce the load, increase the Acc./Dec. time, and consider repairing or replacing the motor. Also, check if the motor overheat terminal (DI or AI terminal) connects incorrectly and detect whether the overheat detection input signal is correct. Ensure that the setting of motor parameter is correct according to nameplate.
What could cause error E19 on hpmont HD5L-PLUS?
Error E19 on your hpmont Controller may arise from a few potential issues. It might be due to an improper setting of V/f curve, so adjust V/f curve. Additionally, check the power input to ensure the mains supply voltage is not too low. Make sure the overload protection factor of the motor is properly set. Finally, the motor blocked-rotor torque or overload could be the cause, so check the load and mechanical transmission devices.
What does 'Lu' mean on hpmont HD5L-PLUS?
The 'Lu' indication on the hpmont Controller has a few possible meanings. It is normal status of power on and power off at the beginning of power on and at the end of power off. It can also indicate that the input voltage is too low, so check input power voltage. Finally, it may be due to improper wiring leading to undervoltage of hardware, so check wiring and wire HD5L-PLUS properly.
What does error E17 mean on hpmont HD5L-PLUS?
Error E17 on the hpmont Controller can occur due to several reasons. The Acc. time may be too short, so adjust Acc. time. It can also be caused by an improper setting of V/f curve or torque boost, so adjust V/f curve or torque boost. Check if the mains supply voltage is too low and ensure the motor load is not too high; if it is, use a controller with proper power rating.
General| Brand | hpmont |
|---|---|
| Model | HD5L-PLUS Series |
| Category | Controller |
| Language | English |
To Next Page
