Icom IC-7700 - Page 205

14-5
D Command table (continued)
14
CONTROL COMMAND
Cmd. Sub Cmd. Data Description
1A 05 0001 see p. 12-4 Send/read SSB RX HPF/LPF
( HPF: 0=Through, 1=100 to 20=2000,
LPF: 5=500 to 24=2400, 25=Through)
0002 00 to 10 Send/read SSB RX Tone (Bass) level
(00 =–5 to 10=+5)
0003 00 to 10 Send/read SSB RX Tone (Treble) level
(00=–5 to 10=+5)
0004 see p. 12-4 Send/read AM RX HPF/LPF
(HPF: 00=Through, 01=100 to
20=2000, LPF: 5=500 to
24=2400, 25=Through)
0005 00 to 10 Send/read AM RX Tone (Bass)
level (00 =–5 to 10=+5)
0006 00 to 10 Send/read AM RX Tone (Treble)
level (00=–5 to 10=+5)
0007 see p. 12-4 Send/read FM RX HPF/LPF
(HPF: 00=Through, 01=100 to
20=2000, LPF: 5=500 to
24=2400, 25=Through)
0008 00 to 10 Send/read FM RX Tone (Bass)
level (00 =–5 to 10=+5)
0009 00 to 10 Send/read FM RX Tone (Treble)
level (00=–5 to 10=+5)
0010 see p. 12-5 Send/read CW RX HPF/LPF
(HPF: 00=Through, 01=100 to
20=2000, LPF: 5=500 to
24=2400, 25=Through)
0011 see p. 12-5 Send/read RTTY RX HPF/LPF
(HPF: 00=Through, 01=100 to
20=2000, LPF: 5=500 to
24=2400, 25=Through)
0012 see p. 12-5 Send/read PSK RX HPF/LPF
(HPF: 00=Through, 01=100 to
20=2000, LPF: 5=500 to
24=2400, 25=Through)
0013 00 to 10 Send/read SSB TX Tone (Bass) level
(00 =–5 to 10=+5)
0014 00 to 10 Send/read SSB TX Tone (Treble) level
(00=–5 to 10=+5)
0015 00 to 10 Send/read AM TX Tone (Bass) level
(00 =–5 to 10=+5)
0016 00 to 10 Send/read AM TX Tone (Treble) level
(00=–5 to 10=+5)
0017 00 to 10 Send/read FM TX Tone (Bass)
level (00 =–5 to 10=+5)
0018 00 to 10 Send/read FM TX Tone (Treble)
level (00=–5 to 10=+5)
0019
see p. 14-12 Send/read SSB TX bandwidth for wide
0020
see p. 14-12 Send/read SSB TX bandwidth for mid
0021
see p. 14-12 Send/read SSB TX bandwidth for
narrow
0022 0000 to
0255
Send/read speech level
(0000=0% to 0255=100%)
0023 0000 to
0255
Send/read CW side tone gain
(0000=min.to0255=max.)
0024 00/01 Send/read CW side tone gain limit
(00=OFF, 01=ON)
0025 0000 to
0255
Send/read beep gain
(0000=min.to0255=max.)
0026 00/01 Send/read beep gain limit
(00=OFF, 01=ON)
0027 0000 to
0255
Send/read headphones output
ratio (0000=0.60 to 0255=1.40)
Cmd. Sub Cmd. Data Description
1A 05 0028 0000 to
0255
Send/read AF output level to ACC
(0000=0% to 0255=100%)
0029 0000 to
0255
Send/read S/P DIF output level
(0000=0% to 0255=100%)
0030 0000 to
0255
Send/read MOD output level to
ACC (0000=0% to 0255=100%)
0031 0000 to
0255
Send/read S/P DIF MOD output
level (0000=0% to 0255=100%)
0032 00 to 03 Send/read MOD input connector
during DATA OFF
( 00=MIC; 01=ACC; 02=MIC/ACC;
03=S/P DIF; 04=LAN)
0033 00 to 03 Send/read MOD input connector
during DATA1
( 00=MIC; 01=ACC; 02=MIC/ACC;
03=S/P DIF; 04=LAN)
0034 00 to 03 Send/read MOD input connector
during DATA2
( 00=MIC; 01=ACC; 02=MIC/ACC;
03=S/P DIF; 04=LAN)
0035 00 to 03 Send/read MOD input connector
during DATA3
( 00=MIC; 01=ACC; 02=MIC/ACC;
03=S/P DIF; 04=LAN)
0036 00/01 Send/read relay type selection
(00=Reed, 01=MOS-FET)
0037 00 to 07 Send/readexternalmeteroutput
selection
(00=Auto, 01=S, 02=Po, 03=SWR,
04=ALC,05=COMP,06=VD,07=ID)
0038 0000 to
0255
Send/readexternalmeteroutput
level (0000=0% to 0255=100%)
0039 00 to 02 Send/read reference signal in/out
setting (00=IN, 01=OFF, 02=OUT)
0040 0000 to
0255
Send/read reference signal frequency
setting (0000=0% to 0255=100%)
0041 0000 to
0255
Send/read LCD unit backlight
brightness (0000=0% to 0255=100%)
0042 0000 to
0255
Send/read switch indicator brightness
(0000=1 to 0255=100)
0043 00 to 01 Send/read screen image type
(00=A, 01=B)
0044 00 to 04 Send/read frequency readout font
(00=Basic (1), 01=Basic (2), 02=Italic,
03=Round, 04=Slim)
0045 00 to 02 Send/read meter response setting
(00=SLOW, 01=MID, 02=FAST)
0046 00 to 02 Send/read meter type
(00=Standard, 01=Edgewise, 02=Bar)
0047 00/01 Send/read meter type during wide
screen or mini scope display
(00=Edgewise, 01=Bar)
0048 00/01 Send/read peak hold set for Bar meter
(00=OFF, 01=ON)
0049 00/01 Send/read memory name display
setting (00=OFF, 01=ON)
0050 00/01 Send/readaudiopeaklterwidth
pop-up display setting
(00=OFF, 01=ON)
0051 00/01 Send/read manual notch width
pop-up display setting
(00=OFF, 01=ON)
0052 00 to 03 Send/read screen saver set
(0=OFF, 01=15 min., 02=30 min.,
03=60 min.)