Icom IC-7700 - Page 206

14-6
D Command table (continued)
14
CONTROL COMMAND
Cmd. Sub Cmd. Data Description
1A 05 0053 00 to 02 Set/read screen saver type
(00=Bound, 01=Rotation, 02=Twist)
0054 00/01 Send/read output signal setting for
externaldisplay(00=OFF,01=ON)
0055 00/01 Send/read synchronous pulse
level setting (00=L, 01=H)
0056 00/01 Send/read opening message display
(00=OFF, 01=ON)
0057
see p. 14-11 Send/read opening message contents
0058 20000101
to
20991231
Send/read date
(20000101=1st Jan. 2000 to
20991231=31st Dec. 2099)
0059 0000 to
2359
Send/read time
(0000=00:00 to 2359=23:59)
0060 00/01 Send/read CLOCK2 function
(00=OFF, 01=ON)
0061
see p. 14-10 Send/read offset time for CLOCK2
(240001=–24:00 to 240000=+24:00)
0062
see p. 14-11 Send/read CLOCK2 name
(up to 3-character)
0063 00/01 Send/read calibration marker
(00=OFF, 01=ON)
0064 00/01 Send/readconrmationbeep
(00=OFF, 01=ON)
0065 00 Band edge beep OFF
01 Band edge beep ON (Beep sounds with
a default amateur band)
02 Band edge beep with user setting ON
03 Band edge beep with user setting/TX
limit ON
0066 0050 to
0200
Send/read beep audio frequency
(0050=500 Hz to 0200=2000 Hz)
0067 00/01 Send/read quick split set
(00=OFF, 01=ON)
0068
see p. 14-11 Send/read FM split offset –9.999 to
+9.999 MHz for HF
0069
see p. 14-11 Send/read FM split offset –9.999 to
+9.999 MHz for 50 MHz
0070 00/01 Send/read split lock set
(00=OFF, 01=ON)
0071 00/01 Send/read tuner auto start set
(00=OFF, 01=ON)
0072 00/01 Send/read PTT tune set
(00=OFF, 01=ON)
0073 00/01 Send/read transverter set
(00=Auto, 01=ON)
0074
see p. 14-11 Send/read transverter offset
0075 00 to 02 Send/read RTTY mark frequency
( 00=1275 Hz, 01=1615 Hz,
02=2125 Hz)
0076 00 to 02 Send/read RTTY shift width
(00=170 Hz, 01=200 Hz, 02=425 Hz)
0077 00/01 Send/read RTTY keying polarity
(00=Normal, 01=Reverse)
0078 00 to 02 Send/read PSK tone frequency
( 00=1000 Hz, 01=1500 Hz,
02=2000 Hz)
0079 00/01 Send/read speech language
(00=English, 01=Japanese)
0080 00/01 Send/read speech speed
(00=Slow, 01=Fast)
0081 00/01 Send/read S-level speech
(00=OFF, 01=ON)
0082 00/01 Send/read speech with a mode switch
operation (00=OFF, 01=ON)
0083 00/01 Send/read memo pad numbers
(00=5 ch, 01=10 ch)
Cmd. Sub Cmd. Data Description
1A 05 0084 00 to 02 Send/read main dial auto TS
(00=OFF, 01=Low, 02=High)
0085 00/01 Send/read mic. up/down speed
(00=Low, 01=High)
0086 00/01 Send/read quick RIT/
:TX clear function
(00=OFF, 01=ON)
0087 00 to 02 Send/read SSB notch operation
(00=Auto, 01=Manual, 02=Auto/Manual)
0088 00 to 02 Send/read AM notch operation
(00=Auto, 01=Manual, 02=Auto/Manual)
0089 00/01 Send/read DIGI-SEL control function
(00=DIGI-SEL, 01=APF)
0090 00/01 Send/read SSB/CW synchronous
tuning function (00=OFF, 01=ON)
0091 00/01 Send/read CW normal side set
(00=LSB, 01=USB)
0092 00/01 Set/read APF type
(00=SHARP, 01=SOFT)
0093 00/01 Send/readexternalkeypadset
for voice memory (00=OFF, 01=ON)
0094 00/01 Send/readexternalkeypadset
for keyer memory (00=OFF, 01=ON)
0095 00/01 Send/readCI-Vtransceiveset
(00=OFF, 01=ON)
0096 00/01 Send/read RS-232C function
(00=CI-V,01=Decode)
0097 00 to 04 Send/read RS-232C decode
Baud rate (00=300, 01=1200, 02=4800,
03=9600, 04=19200)
0098 00 to 10 Send/read keyboard type
(00=English, 01=Japanese,
02=United Kingdom, 03=French,
04=French (Canadian),
05=German, 06=Portuguese,
07=Portuguese (Brazilian),
08=Spanish, 09=Spanish (Latin
American), 10=Italian)
0099 0010 to
0100
Send/read keyboard repeat delay
( 0010=100 msec., 0100=1000 msec.;
50 msec. steps)
0100 00 to 31 Send/read keyboard repeat rate
(00=2.0 cps to 31=30.0 cps)
0101 – Send/read IP address set
(0000000000000001=0.0.0.1 to
0255025502550254=255.255.255.254)
0102 01 to 30 Send/read subnet mask
(01=128.0.0.0 to 30=255.255.255.252)
0103 00/01 Send/read scope display during
TX (00=OFF, 01=ON)
0104 00/01 Send/readscopemax.hold
(00=OFF, 01=ON)
0105 00 to 02 Send/read scope center frequency
set (00=Filter center, 01=Carrier
point center, 02=Carrier point center
(Abs. Freq.))
0106
see p. 14-11 Send/read waveform color for receiving
signal
0107
see p. 14-11 Send/readwaveformcolorformax.hold
0108 00 to 02 Send/read scope sweep speed for ±2.5
kHz span (00=Slow, 01=Mid., 02=Fast)
0109 00 to 02 Send/read scope sweep speed for ±5
kHz span (00=Slow, 01=Mid., 02=Fast)
0110 00 to 02 Send/read scope sweep speed for ±10
kHz span (00=Slow, 01=Mid., 02=Fast)
0111 00 to 02 Send/read scope sweep speed for ±25
kHz span (00=Slow, 01=Mid., 02=Fast)
0112 00 to 02 Send/read scope sweep speed for ±50
kHz span (00=Slow, 01=Mid., 02=Fast)