Parameter List
‑78‑
Parame
ter
Address Name Value Range Default Unit Change
Method
Page
B0‑08 0xB008 Maximum roll
diameter
0.1–6000.0 mm 500 mm In real time "
B0‑08
"
on
page 412
B0‑09 0xB009 Reel diameter 0.1–6000.0 mm 100 mm In real time "
B0‑09
"
on
page 413
B0‑10 0xB00A Initial roll
diameter source
0: B0‑11 to B0‑13 setting
1: AI1 setting
2: AI2 setting
3: AI3 setting
4: Communication setting
(1000H)
0 ‑ At stop "
B0‑10
"
on
page 413
B0‑11 0xB00B Initial roll
diameter 1
0.1–6000.0 mm 100 mm In real time "
B0‑11
"
on
page 413
B0‑12 0xB00C Initial roll
diameter 2
0.1–6000.0 mm 100 mm In real time "
B0‑12
"
on
page 414
B0‑13 0xB00D Initial roll
diameter 3
0.1–6000.0 mm 100 mm In real time "
B0‑13
"
on
page 414
B0‑14 0xB00E Current roll
diameter
0.1–6000.0 mm 100 mm In real time "
B0‑14
"
on
page 414
B0‑15 0xB00F Roll diameter filter
time
0.00s to 10.00s 5 s In real time "
B0‑15
"
on
page 414
B0‑16 0xB010 Winding diameter
change rate
0.0–1000.0 0 ‑ In real time "
B0‑16
"
on
page 415
B0‑17 0xB011 Roll diameter
change direction
limit
0: Disabled
1: Decrease disabled during
winding, and increase
disabled during unwinding
0 ‑ In real time "
B0‑17
"
on
page 415
B0‑18 0xB012 Roll diameter reset
during running
0–1 0 ‑ In real time "
B0‑18
"
on
page 415
B0‑19 0xB013 Pre‑drive speed
gain
‑100.0% to +200.0% 0 % In real time "
B0‑19
"
on
page 416
B0‑20 0xB014 Pre‑charge torque
limit source
0: Set by F2‑09
1: Set based on tension
control torque
1 ‑ At stop "
B0‑20
"
on
page 416
B0‑21 0xB015 Pre‑drive torque
correction
‑100.0% to +100.0% 0 % In real time "
B0‑21
"
on
page 416
B0‑23 0xB017 Pre‑drive
acceleration time
0.0s to 6000.0s 20 s In real time "
B0‑23
"
on
page 417
B0‑24 0xB018 Pre‑drive
deceleration time
0.0s to 6000.0s 20 s In real time "
B0‑24
"
on
page 417
B0‑25 0xB019 Pre‑drive winding
diameter
calculation
0: Disabled
1: Enabled
0 ‑ In real time "
B0‑25
"
on
page 417
B0‑26 0xB01A Tension frequency
limit
0.0% to 100.0% 50 % In real time "
B0‑26
"
on
page 418
To Next Page
Loading...
