Mindray BeneVision N15

To Next Page

To Previous Page

38 - 2 BeneVision N Series Patient Monitor Operator’s Manual

NOTE

• You cannot change timer settings when a timer is running.

• You can set Direct, Run Time, and Reminder Volume only for normal, advanced, and cycled timers.

Main Page

Table of Contents7
Safety33
Safety Information33
Warnings33
Cautions34
Notes34
Equipment Symbols35
Equipment Introduction37
Intended Use37
Applied Parts37
System Components38
N22, N19 Main Unit38
N22, N19 Displays40
N17, N15, N12, N12C Main Unit43
Satellite Module Rack (SMR)47
External Modules47
Cable Management Kit51
Input Devices51
Printing Devices52
Getting Started53
Equipment Preparation Safety Information53
Monitor Installation53
Unpacking and Checking54
Environmental Requirements54
Setting up the Equipment54
Connecting the AC Mains54
Connecting the Input Devices54
Connecting the SMR54
Connecting Modules to the Module Rack or SMR55
Removing Modules from the Module Rack or SMR55
Turning on the Monitor55
Operation and Navigation55
Using the Touchscreen55
Using the Mouse56
Using the On-Screen Keyboard56
Using the Navigation Knob (for N22/N19)56
Using the Barcode Reader56
Using the Remote Controller57
Screen Display57
On-Screen Symbols58
Menus59
Quick Keys59
Operating Modes61
Monitoring Mode62
Privacy Mode62
Night Mode62
Standby Mode63
Configuring Your Monitor64
Setting the Screen Orientation (for N22 and N19)64
Setting the Date and Time64
Adjusting the Screen Brightness64
Adjusting the Volume65
Starting Monitoring a Patient65
Stopping a Parameter Measurement65
General Operation65
Switching on or off a Parameter65
Displaying Parameter Numerics and Waveforms65
Displaying the Parameter List66
Accessing Parameter Setup Menus66
Changing Measurement Colors66
Freezing Waveforms66
Viewing Frozen Waveforms67
Unfreezing Waveforms67
Printing Frozen Waveforms67
Using Secondary Displays67
Connecting the Secondary Display Power Supply (for N22/N19)67
Changing Secondary Display Settings68
Setting the ECG Waveform Size for the Independent External Display (for N17/N15/N12)68
Using the Iview System69
Using the Nview Remote Displays69
Recommended Hardware and Network Requirements70
Installing the Nview Tool70
Manually Starting Remote Screen71
Configuring the Remote Screen71
Setting the ECG Waveform Size for the Remote Screen71
Selecting a Different Monitor for Nview72
Restarting a Remote Screen72
Closing Remote Screens72
Capturing the Screen73
Checking Software Licenses73
Turning off the Monitor73
User Screens75
Choosing a Screen75
Normal Screen75
Entering the Normal Screen75
Configuring the Normal Screen75
The Big Numerics Screen75
Entering the Big Numerics Screen75
Configuring the Big Numerics Screen76
Minitrends Screen76
Entering the Minitrends Screen76
The Display of Minitrends Screen77
Setting Minitrends Parameters77
Setting the Minitrend Length77
Setting the Alarm Statistics Switch77
Setting the Alarm Statistics Length78
Routine Vital/Baseline78
The Oxycrg Screen78
Entering the Oxycrg Screen78
Oxycrg Events79
The Display of the ABD Event Area79
Setting Oxycrg Parameters79
Setting the Threshold of ABD Events79
Editing ABD Events79
The Spo2 Screen80
Entering the Spo2 Screen80
The Display of Spo2 Screen80
Operating the Spo2 Screen80
Managing Patients81
Discharging a Patient81
Manually Discharging a Patient81
Admitting a Patient81
Managing Patient Information82
Entering the Patient Management Menu82
Editing Patient Information82
Loading Patient Information from the CMS82
Loading Patient Information from the ADT Server82
Transferring Patient83
Data Storage Introduction83
Transferring Patient Data84
Exporting Patient Data84
Deleting Patient Data85
Managing Configurations87
Configuration Introduction87
Changing the Department87
Setting Default Patient Category87
Setting Default Configuration87
Saving Current Settings88
Deleting a Configuration88
Transferring a Configuration88
Exporting a Configuration88
Importing a Configuration89
Printing Configurations89
Loading a Configuration89
Modifying Configuration Password89
Networked Monitoring91
Network Introduction91
Network Safety Information91
Connecting the Monitor to the CMS91
Connecting the Egateway92
Viewing Other Patients92
Remote View92
Alarm Watch94
Mldap95
Disconnecting the Wireless Network95
Pairing Introduction97
Pairing and Unpairing Symbols97
Pairing a TM80 with the Monitor97
Pairing Procedure98
System Responses after Pairing a TM80 with the Monitor98
Unpairing the TM80 and the Monitor99
Unpairing Via the Monitor99
Unpairing Via the TM8099
Pairing a BP10 with the Monitor100
Pairing Procedure100
System Responses after Pairing the BP10 with the Monitor100
Unpairing the BP10 and the Monitor101
Unpairing Via the Monitor101
Unpairing Via the BP10101
NIBP Measurement in Sequence or ABPM Mode101
Performing NIBP Measurement in Sequence Mode101
Performing NIBP Measurement in ABPM Mode101
Troubleshooting102
Interfacing with External Devices105
Benelink Introduction105
Benelink Safety Information105
Differences in Displayed Values106
Connecting an External Device106
Accessing the Integrated Devices Screen107
Displaying Parameters from External Devices108
Setting Waveform Properties for Parameters from External Devices108
Setting Alarms from External Devices108
Setting Parameters from External Devices for Display108
Setting Units for Parameters from External Devices109
Accessing the Loops Screen109
Viewing Alarms from External Devices109
Viewing Parameter Trends from External Devices109
Recording and Printing Parameter Trends from External Devices109
Alarms111
Alarm Introduction111
Alarm Safety Information111
Understanding the Alarms111
Alarm Categories111
Alarm Priorities112
Alarm Indicators112
Alarm Status Symbols113
Accessing On-Screen Help for Technical Alarms (Alarmsight)113
Checking Physiological Alarm List113
Changing Alarm Settings113
Setting Parameter Alarm Properties113
Setting Alarm Tone Properties113
Setting the Auto Limits for New Patient Switch114
Initiating Auto Alarm Limits114
Setting the Alarm Delay Time117
Adjusting the Alarm Light Brightness117
Restoring the Default Alarm Settings118
10.6.8 Setting the Length of Printed Waveforms118
Setting the Switch of the Spo Desat Alarm off118
10.6.10 Setting the Switch of the Apnea Alarm off118
Pausing Alarms/Pausing Alarm Tones118
Defining the Pause Function118
10.7.2 Pausing Alarms118
Switching off All Alarms119
Pausing Alarm Sound119
Resetting Alarms120
Resetting Physiological Alarms120
Resetting Technical Alarms120
Latching Alarms120
Nurse Call121
Calling for Help121
CPB Mode121
10.12.1 Entering the CPB Mode121
10.12.2 Exiting the CPB Mode122
Intubation Mode122
10.13.1 Entering the Intubation Mode122
10.13.2 Exiting the Intubation Mode122
Testing Alarms122
Actions When an Alarm Occurs122
Monitoring ECG, Arrhythmia, ST and QT123
ECG Introduction123
ECG Safety Information123
ECG Display124
Preparing for ECG Monitoring125
Preparing the Patient Skin125
Applying Electrodes125
Lead Wire Color Code126
ECG Electrode Placements126
Choosing the ECG Lead Type128
Checking Paced Status128
Enabling Pacer Rejection129
Using 6-Lead Placement to Derive 12-Lead ECG (D12L)129
Changing ECG Settings129
Choosing an ECG Screen129
Setting ECG Alarm Properties130
Setting the Analysis Mode130
Changing ECG Wave Settings130
Disabling the Smart Lead off Function132
Disabling the Crozfusion Function132
Adjusting the QRS Volume133
Adjusting the Minimum QRS Detection Threshold133
Monitoring Arrhythmia134
Arrhythmia Safety Information134
Arrhythmia Events134
Displaying Arrhythmia Information135
Changing Arrhythmia Settings136
Arrhythmia Alarms Timeout138
ST Segment Monitoring140
ST Safety Information140
Enabling ST Monitoring140
Displaying ST Numerics141
Displaying ST Segments in the Waveform Area141
Entering the ST View142
Saving the Current ST as Baseline142
Entering the ST Graphic Window143
Changing ST Settings143
Adjusting ST Measurement Points145
Qt/Qtc Interval Monitoring146
Qt/Qtc Monitoring Limitations146
Enabling Qt/Qtc Monitoring146
Displaying Qt/Qtc Numerics and Segments146
Entering the QT View147
Saving the Current Qtc as Baseline148
Changing QT Settings148
ECG Relearning148
11.10.1 Auto ECG Relearning148
11.10.2 Initiating an ECG Relearning Manually148
Calibrating ECG149
Defibrillation Synchronization Pulse Output149
ECG Troubleshooting149
Resting 12-Lead ECG Analysis151
Resting 12-Lead ECG Analysis Introduction151
Entering the 12-Lead Screen151
Initiating Resting 12-Lead ECG Analysis151
Changing 12-Lead ECG Analysis Settings151
Setting the High Frequency Filter151
Setting the Baseline Drift Removal152
Glasgow Resting 12-Lead ECG Analysis Algorithm Settings152
Editing Patient Information (for Glasgow Algorithms)152
Setting Tachycardia and Bradycardia Thresholds (for Glasgow Algorithms)153
Setting the 12-Lead Interpretation Report (for Glasgow Algorithms)153
Saving the 12-Lead Interpretation Report153
Printing the 12-Lead Interpretation Report153
Exiting the ECG 12-Lead Screen153
Monitoring Respiration (Resp)155
Resp Introduction155
Resp Safety Information155
Resp Display156
Preparing for Resp Monitoring156
Preparing the Patient156
Placing the Electrodes157
Changing Resp Settings158
Setting the Resp Alarm Properties158
Setting the RR Source158
Choosing the Respiration Lead158
Setting the Resp Waveform Size158
Setting the Resp Waveform Speed158
Setting the Auto Detection Switch159
Adjusting the Resp Waveform Detection Threshold159
Resp Troubleshooting159
Monitoring Pulse Oxygen Saturation (Spo )161
Spo Introduction161
Spo Safety Information162
Spo Measurement Limitations163
Spo Display164
Preparing for Spo Monitoring164
Changing the Spo Settings165
Changing the Spo Alarm Settings165
Nellcor Sat-Seconds Alarm Management165
Setting the Nellcor Spo Sat-Seconds166
Changing Sensitivity167
Showing/Hiding PI167
Monitoring Spo 2 and NIBP Simultaneously167
Changing the Sweep Speed of the Pleth Wave168
Changing the PR Settings168
Changing the PR Alarm Settings168
Changing the QRS Volume168
Setting the PR Source168
Showing/Hiding PR168
Spo Troubleshooting169
Nellcor Information170
Monitoring Temperature (Temp)173
Temperature Introduction173
Displaying the Temp Numerics Area173
Temperature Display (for MPM and Temp Module)174
Preparing for Temperature Monitoring (for MPM and Temp Module)174
Changing Temperature Settings (for MPM and Temp Module)174
Setting the Temperature Alarm Properties (for MPM and Temp Module)174
Selecting the Temperature Label (for MPM and Temp Module)174
Displaying the Temperature Difference (for MPM and Temp Module)174
Tympanic Temperature Display175
Measuring the Tympanic Temperature175
Temperature Troubleshooting176
Monitoring Noninvasive Blood Pressure (NIBP)177
NIBP Introduction177
NIBP Safety Information178
NIBP Measurement Limitations178
Measurement Modes179
NIBP Display179
Preparing for NIBP Measurements180
Preparing the Patient for NIBP Measurements180
Placing the NIBP Cuff180
Starting and Stopping NIBP Measurements181
Changing NIBP Settings181
Setting the NIBP Alarm Properties181
Setting the Initial Cuff Inflation Pressure181
Setting the NIBP Interval181
Selecting NIBP Start Mode182
Enabling the NIBP End Tone182
Setting NIBP Sequence182
Setting the NIBP Display Format182
Setting the NIBP Alarm Limits Display Switch182
Showing/Hiding PR182
16.8.10 Correcting the NIBP Measurements183
Assisting Venous Puncture183
NIBP Maintenance183
16.10.1 NIBP Leakage Test183
16.10.2 NIBP Accuracy Test183
NIBP Troubleshooting183
Monitoring Invasive Blood Pressure (IBP)185
IBP Introduction185
IBP Safety Information185
Preparing for IBP Monitoring186
IBP Equipment to Patient Connection186
Measuring an Invasive Blood Pressure186
Zeroing the IBP Transducer187
Measuring ICP Using the Codman ICP Transducer187
Zeroing the Codman ICP Transducer187
Measuring ICP187
IBP Display188
Changing IBP Settings189
Changing the IBP Alarm Settings189
Changing the Pressure Label189
Setting the Pressure Type for Display189
Changing the Sensitivity189
Setting the IBP Waveform190
Setting the Display Format of Artery Pressure190
Showing/Hiding the Alarm Limits of Artery Pressure190
Setting the Use PA-D as PAWP Switch190
Enabling PPV Measurement190
17.6.10 Overlapping IBP Waveforms191
Measuring PAWP192
PAWP Equipment to Patient Connection192
Preparing to Measure PAWP193
Measuring PAWP193
Setting the Waveforms of the PAWP Screen194
Performing Hemodynamic Calculation194
Connecting a Camino Device194
IBP Troubleshooting195
Monitoring Cardiac Output (C.O.)197
C.O. Introduction197
C.O. Safety Information197
C.O. Measurement Limitations198
C.O. Display198
C.O. Equipment to Patient Connection199
Performing C.O. Measurement199
Preparing for C.O. Measurement199
Setting C.O. Measurement199
Performing C.O. Measurement200
Changing C.O. Settings201
Setting C.O. Alarm Properties201
Selecting the Primary C.O. Parameter201
Troubleshooting202
Monitoring Central Venous Oxygen Saturation (Scvo )203
Scvo Introduction203
Scvo Safety Information203
Scvo Display203
Accessing the On-Screen Scvo204
Guide204
Scvo 2 Equipment to Patient Connection204
Measuring Scvo204
Scvo Calibration205
Accessing the Hemosight Menu205
Changing Scvo Settings205
Changing Scvo Alarm Settings205
Setting Hb/Hct205
Inputting the Sao206
Value206
Monitoring Cco/Svo207
Cco/Svo Introduction207
Cco/Svo Safety Information208
CCO Display208
Svo /Scvo Display208
Connecting the Device208
Cco/Svo2 Cable208
Connecting to the Vigilance II Monitor209
Connecting to the Vigileo Monitor210
Connecting the EV1000 Monitor211
Connecting the Hemosphere Monitor212
Accessing the Hemosight Menu213
Changing CCO Settings213
Changing the CCO Alarm Settings213
Changing the SVR Unit213
Setting Parameters for Display213
Setting the CCO Analog Output Signal213
Changing Svo /Scvo Settings214
Changing the Svo /Scvo Alarm Settings214
Setting the Svo /Scvo Analog Output Signal214
Cco/Svo Troubleshooting215
Monitoring Impedance Cardiography (ICG)217
ICG Introduction217
ICG Safety Information217
ICG Measurement Limitations218
ICG Display218
Accessing the On-Screen ICG Guide218
Preparing for ICG Monitoring218
Preparing the Skin219
Placing the ICG Sensors219
Connecting the ICG Patient Cable220
Changing ICG Settings220
Changing ICG Alarm Settings220
Changing Patient Information220
Changing the ICG Wave Sweep Speed221
Selecting ICG Parameters221
ICG Troubleshooting221
Monitoring Continuous Cardiac Output (from Picco Module)223
CCO Introduction223
CCO Safety Information223
Zeroing the IBP Transducer224
Picco Display224
CCO Display224
Part Display225
Pcvp Display225
Accessing the On-Screen CCO Guide225
CCO Equipment to Patient Connection226
Preparing to Monitor C.O226
Performing the CCO Settings227
Performing C.O. Measurement228
Accessing the Hemosight Menu229
Changing CCO Settings229
Changing CCO and CCI Alarm Settings229
Setting Parameters for Display229
Picco Troubleshooting230
Monitoring Carbon Dioxide (CO )231
CO Introduction231
CO Safety Information232
CO Measurement Limitations232
CO Display232
Measuring CO 2 Using Sidestream/Microstream CO 2 Module233
Preparing to Measure CO233
Using Sidestream CO 2 Module233
Preparing to Measure CO Using Microstream CO Module235
Zeroing the Sidestream/Microstream CO Module235
Measuring CO Using Mainstream CO Module236
Preparing to Measure CO236
Zeroing the Mainstream CO Sensor237
Changing Settings for All CO Modules237
Changing CO Alarm Settings237
Setting the CO Waveform237
Setting the RR Source237
Entering the Standby Mode238
Entering the Intubation Mode238
Changing Settings for Sidestream and Microstream CO Module238
Setting the Auto Standby238
Setting Humidity Compensation238
Changing O Settings (for Sidestream CO Module Integrating O )239
Changing O Alarm Settings239
Setting the O Waveform239
Setting the Gas Compensation239
Choosing a Time Interval for Peak-Picking240
Changing Barometric Pressure240
Performing the Leakage Test240
CO Calibration240
CO Troubleshooting240
Troubleshooting the Sidestream/Microstream CO 2 Module241
Troubleshooting the Mainstream CO Module241
Oridion Information241
Monitoring Anesthetic Gas (AG)243
AG Introduction243
AG Safety Information244
AG Measurement Limitations244
AG Display244
AG Equipment to Patient Connection245
Preparing for AG Monitoring245
MAC Values246
Changing AG Settings247
Changing AG Alarm Settings247
Setting the O Compensation247
Entering the Standby Mode247
Setting Auto Standby247
Setting the Gas Waveform247
Setting the RR Source248
Entering the Intubation Mode248
Enabling or Disabling MAC Display248
Changing the Anesthetic Agent248
Performing AG Leakage Test249
Calibrating the AG Module249
AG Troubleshooting249
Monitoring Respiratory Mechanics (RM)251
RM Introduction251
RM Safety Information251
RM Parameters251
RM Display252
RM Equipment to Patient Connection253
Preparing for RM Monitoring253
Respiratory Loops254
Changing the Loop Type255
Saving the Loop as Reference255
Displaying the Reference Loop255
Adjusting the Loop Scale255
Selecting the Parameters for Display255
Changing RM Settings255
Changing RM Alarm Settings255
Setting the Apnea Alarm Delay256
Setting RR Source256
Changing the Wave Sweep Speed256
Changing the Wave Scale256
Setting the Ambient Temperature256
Setting the Ambient Humidity256
Setting Parameters for Display257
Entering the Intubation Mode257
VCO 2 and Metabolic Monitoring257
And Metabolic Parameters257
Safety Information When RM Module in Use with CO or AG Module258
Measurement Limitations When RM Module in Use with CO or AG Module258
Equipment to Patient Connection When RM Module in Use with CO259
25.9.5 Displaying the VCO2 and EE Numerics Areas260
Preparing for VCO2 and Metabolic Monitoring260
Viewing V-CO260
Curve260
Selecting the Displayed VCO 2 Parameters260
RM Troubleshooting260
Monitoring Transcutaneous Blood Gas (Tcgas)263
Tcgas Introduction263
Tcgas Safety Information263
Connecting an External Device263
Tcgas Parameters264
Activating the Tcgas Alarm Sound264
Monitoring Electroencephalogram (EEG)265
EEG Introduction265
EEG Safety Information265
EEG Parameters266
EEG Display266
Accessing the On-Screen EEG Guide267
Prepare for EEG Monitoring267
EEG Equipment to Patient Connection267
Choosing an EEG Electrode Montage268
Attaching EEG Electrodes270
Performing EEG Sensor Check270
Setting the Interval of Auto Sensor Check270
Displaying/Hiding Impedance Value271
Manually Starting a Sensor Check271
EEG Electrode Status271
Stopping Sensor Check272
Changing EEG Settings272
Changing the EEG Scale272
Changing the EEG Sweep Speed272
Changing the High/Low Filter272
Switching off the Notch Filter272
Changing Displayed EEG Parameters272
Displaying the EEG Expand View273
CSA View273
DSA View274
EEG Troubleshooting275
Monitoring Bispectral Index (BIS)277
BIS Introduction277
BIS Safety Information278
BIS Parameters279
BIS Display280
Accessing the On-Screen bis Guide280
Preparing for bis Monitoring281
Changing bis Settings282
Setting bis Alarm Properties282
Choosing the bis Smoothing Rate282
Setting the Display of bis Waveform Area282
Switching off the Filter282
Setting the Displayed bis Parameters282
Sensor Check283
Automatic Sensor Check283
Disabling Automatic Sensor Check283
Manual Sensor Check283
BIS Sensor Status284
Monitoring Bilateral bis284
Entering the bis Expand View284
Selecting bis Expand View Display284
BIS Troubleshooting285
Monitoring Neuromuscular Transmission (NMT)287
NMT Introduction287
NMT Safety Information287
Stimulation Modes288
Train-Of-Four (TOF)288
Single Twitch (ST)288
Post-Tetanic Count (PTC)288
Double Burst Stimulation (DBS)289
NMT Parameters289
NMT Display289
Accessing the On-Screen NMT Guide290
Preparing for NMT Monitoring290
NMT Equipment to Patient Connection290
Preparing the Skin291
Placing the Electrodes and Sensor291
Calibrating the NMT Measurement292
Setting the Calibration Current292
Starting NMT Calibration292
Starting NMT Measurements293
Stopping NMT Measurements293
Changing NMT Measurement Settings293
29.11.1 Selecting the NMT Measurement Mode293
29.11.2 Changing the Stimulation Current293
29.11.3 Changing the Pulse Width293
29.11.4 Enabling Block Recovery Notification294
29.11.5 Adjusting NMT Stimulation Tone Volume294
Recalling Calibration Information294
NMT Troubleshooting294
Monitoring NMT from TOF-Watch SX Monitor295
NMT Introduction295
NMT Safety Information295
Connecting a TOF-Watch SX Monitor295
NMT Parameters296
NMT Display296
Changing NMT Settings297
Activating the NMT Alarm Sound297
Viewing the Measurement Setup297
Monitoring Regional Oxygen Saturation (Rso )299
Rso2 Introduction299
Rso2 Safety Information300
Rso Measurement Limitations300
Rso Display300
Accessing the On-Screen Rso301
Guide301
Preparing for Rso Monitoring301
Rso Sensor Site Selection301
Preparing the Skin301
Applying the Rso Sensor302
Connecting the Rso Parts302
Changing Rso Settings303
Changing Rso Alarm Settings303
Setting the Rso Auto Low Limit Switch303
Setting the Rso Label303
Setting the AUC Mode303
Setting the Baseline303
Selecting Rso 2 Parameters for Display304
Review305
Review Overview305
Review Page305
Accessing the Review Page305
Example Review Page305
Symbols on Review306
Common Operations306
Tabular Trends Review Page307
Graphics Trends Review Page308
Events Review Page309
Full Disclosure Review Page310
Oxycrg Review Page311
32.2.10 12-Lead ECG Review Page312
32.2.11 ST Review Page313
Reviewing Discharged Patients314
Checking the Data of a Discharged Patient314
Checking the Information of a Discharged Patient314
Hemosight TM315
Hemosight Introduction315
Accessing the Hemosight Menu315
Viewing Hemodynamic Parameters315
Physiology Graphics320
Physiology Relationship322
Decision Model (Only Available for Picco Module)323
Hemodynamic Test323
Renaming a Test323
Setting Test Time Duration323
Selecting Parameters for Testing323
Performing a Hymodynamic Test324
Following up the Patient Hemodynamic Status324
Cardiac Function Curve and Lung Water Curve324
Setting the Cardiac Function Curve and Lung Water Curve325
SVV/PPV Slope Indicator325
Setting the SVV/PPV Slope Indicator325
Evaluating the Hemodynamic Parameters326
Viewing the Spider Vision Diagram326
Viewing Trends326
Viewing Hemodynamic Prameters327
Changing the Time Length of Trends327
Selecting the Pattern327
Saving Reference Values327
Changing Hemodynamic Parameter Settings328
Setting Hemodynamic Parameter Ranges328
Restoring Default Values328
Setting the Pattern328
Clinical Assistive Applications (CAA)329
Boa Dashboard329
Accessing Boa Dashboard329
Induction330
Maintenance331
Recovery332
Setting the Boa Dashboard332
Early Warning Score (EWS)333
Displaying the EWS Numerics Area334
Accessing the EWS Screen335
Performing EWS Scoring336
EWS Alarm336
Changing EWS Settings337
Glasgow Coma Scale (GCS)338
Displaying the GCS Parameter Area338
Accessing the GCS Menu339
Performing GCS Scoring339
Setting GCS Scoring Interval339
Reviewing GCS Trend Data339
Sepsissight340
Accessing the Sepsissight Menu340
Screening340
Recommendations341
Reviewing Sepsissight Trend Data341
Rescuing Mode341
Entering the Rescue Mode342
Monitoring CPR342
CPR Dashboard343
Exit the Rescue Mode344
ECG 24H Summary344
Viewing the ECG 24H Summary344
Selecting Typical ECG Strips344
Reviewing ECG Summary345
Pace View345
Accessing Pace View345
Viewing the Current Pace Pulse345
Viewing Historic Pace Events345
Infusionview346
Entering the Infusionview346
The Display of Infusionview347
Selecting Trend Parameters and Target Values347
Setting the Minitrend Length348
Calculation349
Calculation Overview349
Calculation Safety Information349
Drug Calculations349
Performing Drug Calculations349
Checking the Titration Table350
Drug Calculation Formula350
Titration Table Calculation Formula350
Renal Calculations355
Performing Renal Calculations355
Calculated Parameters and Formulas for Renal Calculations355
Recording357
Recorder357
Starting Recordings357
Manually Starting Recordings357
Automatic Recordings357
Stopping Recordings358
Stopping Recordings Manually358
Stopping Recordings Automatically358
Recording Related Flags358
Setting the Recorder358
Enabling Auto Recording on Alarm358
Clearing Recording Tasks359
Loading Paper359
Removing Paper Jam360
Printing361
Supported Printer361
End Case Reports361
Printing the End Case Report361
Setting a Report as an End Case Report361
Setting the End Case Report362
Setting the End Case Report Period362
Manually Starting a Printing Task362
Starting Printing from the Current Page362
Printing Realtime Reports362
Printing Normal Reports362
Automatically Printing Reports362
Stopping a Printing Task363
Setting Reports363
Setting ECG Reports363
Setting Realtime Reports364
Setting Tabular Trends Reports364
Setting Graphic Trends Reports364
Viewing Printer Status365
Printer out of Paper365
Using the On-Screen Timers367
Displaying Timers367
Controlling the Timer367
Setting the Timer367
User Maintenance Settings369
Accessing the Maintenance Menu369
The Device Location Settings369
The Patient Management Settings370
The Field Tab370
The ADT Query Tab370
The Transfer Tab370
The Discharge Tab371
The Location Tab371
The Display Tab372
The Alarm Settings372
The Audio Tab372
The Pause/Reset Tab373
The Latching Tab374
The Remote View Tab374
The Nurse Call Tab375
The Other Tab375
The CAA Settings376
The EWS Tab376
The GCS Tab377
The CPR Tab377
The Module Settings377
The ECG Tab377
The Other Tab377
The Review Settings378
The Tabs Tab378
The Event Tab378
The Arrhy Mark Tab378
The Display Settings379
The Print Settings379
The Printer Tab379
The Report Layout Tab380
The ECG Report Tab380
The PDF File Name Tab380
The Other Tab380
The Unit Settings381
The Time Settings381
The Other Settings381
The Authorization Setup Settings382
The Version Settings383
The Battery Information Settings383
The Scanner Settings383
The 2D Barcode Tab (for the Mindray Custom 2D Barcode Reader)383
39.16.2 the 1D Barcode Tab383
39.16.3 the Scanner Information Tab384
The Identify Scanner Tab (for the Non-Mindray Custom 2D Barcode Reader)384
The Field Tab (for the Mindray Custom 2D Barcode Reader)384
The Network Setup Settings384
39.17.1 the Network Type Tab384
39.17.2 the LAN1 IP Tab384
39.17.3 the WLAN Tab385
39.17.4 the WLAN IP Tab385
39.17.5 the Central Station Setup Tab385
39.17.6 the Device Discover Tab386
39.17.7 the Qos Tab386
39.17.8 the ADT Tab386
39.17.9 the HL7 Configuration Tab386
39.17.10 the Information Security Tab387
39.17.11 the MLDAP Tab387
The Wireless Module Settings388
Battery389
Battery Introduction389
Battery Safety Information389
Installing or Replacing the Battery390
Battery Indications391
Battery LED391
Battery Power Indicators391
Battery-Related Alarms391
Charging the Battery391
Maintaining the Battery392
Conditioning the Battery392
Checking Battery Performance392
Storing Batteries392
Recycling Batteries393
Care and Cleaning395
Care and Cleaning Introduction395
Care and Cleaning Safety Information395
Cleaning the Monitor/Module/Smr395
Disinfecting the Monitor/Module/Smr396
Cleaning and Disinfecting the Accessories398
Cleaning the Accessories398
Disinfecting the Accessories398
Sterilization401
Cleaning the Thermal Print Head401
Impact of Improper Cleaning402
Maintenance Introduction403
Maintenance Safety Information403
Maintenance and Testing Schedule404
Testing Methods and Procedures404
Performing Visual Inspection404
Performing Power-On Test405
Checking the NMT Sensor405
Testing the Recorder405
Testing the Network Printer405
Checking the Battery405
Disposing of the Monitor406
Accessories407
ECG Accessories407
ECG Electrodes407
12-Pin Trunk Cables407
6-Lead ECG Leadwires409
Spo Accessories409
Extension Cables410
Mindray Spo410
Sensors410
Nellcor Spo410
Temp Accessories411
Temp Cable411
Temp Probes411
Tympanic Temperature Accessories411
NIBP Accessories411
NIBP Hoses411
Cuffs411
IBP Accessories413
ICP Accessories413
C.O. Accessories413
Scvo Accessories413
Picco Accessories414
ICG Accessories414
CO Accessories414
Sidestream CO Accessories414
Microstream CO Accessories415
Mainstream CO Accessories415
AG Accessories416
RM Accessories416
EEG Accessories416
BIS Accessories416
Rso 2 Accessories417
Benelink Accessories417
Mount and Mounting Accessories418
Miscellaneous Accessories419
External Modules421
Physical Specifications423
Benevision N17/N15/N12/N12C423
Environmental Specifications425
Battery Specifications426
Display Specifications427
Touchscreen Specifications427
Recorder Specifications427
Leds427
Audio Indicator428
Monitor Interface Specifications428
Interface Specifications of the N22/N19 Main Unit428
Interface Specifications of the N22/N19 Separate Primary Display428
Interface Specifications of the N22/N19 Integrated Primary Display428
Interface Specifications of the N22/N19 Secondary Display428
Interface Specifications of the N17/N15/N12/N12C429
Signal Outputs Specifications429
Data Storage430
Wi-Fi Specifications430
Wi-Fi Technical Specifications430
Wi-Fi Performance Specifications430
MPAN Specifications432
MPAN Technical Specifications432
MPAN Performance Specifications432
Measurement Specifications433
ECG Specifications433
Resp Specifications435
Spo Specifications436
PR Specifications438
Temp Specifications439
Temp Specifications from Genius439
TM 2 Tympanic Thermometer439
NIBP Specifications442
IBP Specifications442
A.15.10 Scvo2/Svo2 Specifications443
A.15.11 CCO Specifications444
A.15.12 ICG Specifications446
CO Specifications446
A.15.14 AG Specifications450
A.15.15 RM Specifications454
A.15.16 EEG Specifications456
Rso Specifications458
B EMC and Radio Regulatory Compliance459
Emc459
Radio Regulatory Compliance463
C Default Settings465
Parameters Default Settings465
ECG, Arrhythmia, ST and QT Default Settings465
Spo470
Temperature Default Settings471
NIBP Default Settings471
IBP Default Settings473
Scvo Default Settings477
CCO Default Settings (Picco)477
ICG Default Setting477
CO Default Settings479
Gas Default Settings480
RM Default Settings482
EEG Default Settings483
BIS Default Settings484
NMT Default Settings484
Rso Default Settings485
Routine Default Settings485
Alarm Default Settings485
Review Default Settings486
Minitrends Default Settings486
Oxycrg Default Settings487
Display Default Settings487
Report Default Settings487
Calculations Default Settings488
System Time Default Settings488
Physiological Alarm Messages491
General Physiological Alarm Messages491
Arrhythmia Alarm Messages491
Resp Physiological Alarm Messages492
Spo Physiological Alarm Messages492
PR Physiological Alarm Messages492
NIBP Physiological Alarm Messages492
D.1.7 IBP Physiological Alarm Messages492
CO Physiological Alarm Messages493
AG Physiological Alarm Messages493
RM Physiological Alarm Messages493
EWS Physiological Alarm Messages493
Technical Alarm Messages493
General Technical Alarm Messages494
ECG Technical Alarm Messages494
Resp Technical Alarm Messages494
Spo Technical Alarm Messages495
Temp Technical Alarm Messages495
NIBP Technical Alarm Messages496
IBP Technical Alarm Messages496
Scvo Technical Alarm Messages497
ICG Technical Alarm Messages497
CCO Technical Alarm Messages (from Picco Module)498
CO Technical Alarm Messages498
AG Technical Alarm Messages500
RM Technical Alarm Messages500
BIS Technical Alarm Messages500
EEG Technical Alarm Messages501
NMT Technical Alarm Messages502
Rso Technical Alarm Messages502
EWS Technical Alarms503
Power Supply Technical Alarm Messages503
Recorder Technical Alarm Messages503
Printer Technical Alarm Messages504
Technical Alarm Messages Related to Networked Monitoring504
Technical Alarm Messages Related to Telemetry Monitors and BP10 Modules505
Other System Technical Alarm Messages506
Power Cord Plug507
Device Enclosure and Accessories507
Visual Inspection507
Contextual Inspection508
Device Labeling508
Protective Earth Resistance508
Earth Leakage Test508
Patient Leakage Current509
Mains on Applied Part Leakage509
Patient Auxiliary Current510
Preprocessing511
QRS Typing511
Selection of Required QRS Class511
Averaging511
Wave Measurement511
QRS Components511
ST Segment511
Units515
Symbols516
Abbreviations517

Mindray BeneVision N15

Table of Contents

Other manuals for Mindray BeneVision N15

Related product manuals