47
CHAPTER 3 SPECIFICATIONS
3
3.2 Function Lists
: Available, : Partially available, ×: N/A
*1 Data of station No.65 and higher in other stations cannot be received.
*2 Cyclic data are sent to or received from the stations whose own send ranges are assigned to LB/LW 0 to 3FFF in "LB/LW
Setting(1)".
*3 Direct access to LB/LW4000 and higher is not allowed.
*4 The function is not available in the Q00UJCPU, Q00UCPU, or Q01UCPU.
(2) List of transient transmission functions
Online
operation
Stop/restart of cyclic
transmission
Disables receiving data from other stations and
sending data of its own station in a case such as
debugging. (Transient transmission is not
stopped.)
Page 91,
Section 4.1.12
1) Safety CPU
2) Basic model QCPU
3) High Performance model QCPU
4) Process CPU
5) Redundant CPU
6) Universal model QCPU
Function Description
CPU module
Reference
section
1) 2) 3) 4) 5) 6)
Link
dedicated
instruction
Read from/write to
other station devices
(for Q/QnA series)
Reads or writes data from or to devices of a
programmable controller on another station.
(READ/SREAD/WRITE/SWRITE instruction)
*1
*2
*3
*1 *1 *1 *1
Page 97,
Section 4.2.1
Page 324,
CHAPTER 9
Transient request to
another station (for
Q/QnA series)
Remotely runs or stops a programmable controller
on another station. (REQ instruction)
×
*1 *1 *1 *1
Reads or writes clock data from or to a
programmable controller on another station. (REQ
instruction)
*1
*2
*1 *1 *1 *1
Data send/receive (for
Q/QnA series)
Sends data to a programmable controller on
another station. (SEND instruction)
Reads data received from a programmable
controller on another station. (RECV/RECVS
instruction)
×
*1 *1 *1 *1
Read from/write to
other station devices
(For A series)
Reads or writes data from or to devices of a
programmable controller on another station.
(ZNRD/ZNWR instruction)
×
*7 *7 *7 *7 *7
Remote RUN/STOP
(For Q series)
Remotely run or stop a programmable controller
on another station. (RRUN/RSTOP instruction)
×
*1 *1 *1 *1
Read/write of another
station's clock data
(For Q series)
Reads or writes clock data from or to a
programmable controller on another station.
(RTMRD/RTMWR instruction)
*1
*2
*1 *1 *1 *1
CC-Link
dedicated
instruction
Read/write of another
station's data
Reads or writes the specified points of data from
the target station's device. (RIRD/RIWT
instruction)
*5
×
Access to other stations with a
programming tool
With a programming tool allows seamless access
to the Ethernet, CC-Link IE Controller Network,
MELSECNET/H, MELSECNET/10, CC-Link IE
Field Network, and CC-Link systems.
*1
*4
*1 *1 *1 *1
Page 97,
Section 4.2
Group
By specifying transient transmission target stations
as a group, data can be sent to all stations of the
same group No.
Page 102,
Section 4.2.2
Routing
Allows transient transmissions to stations located
on other networks in a multi-network system.
*6 *6 *6 *6 *6
Page 103,
Section 4.2.3
Function Description
CPU module
Reference
section
1) 2) 3) 4) 5) 6)
To Next Page
Loading...
