Motion Control Engineering Nidec Element Series

Index-8 Manual # 42-02-2P26
Inventory hall calls 1-45
IO Terminal Mapping Flt message 2-72
IO1 - IO8 2-46
IP 2-26
IP Address 2-15
Itinerary Manager 2-16, 2-17
Itinerary manager 1-15
J
Job Department and Year 2-5
Job Info and Labels 2-5
Job Name 2-5
Job Number 2-5
JP1, CDBPTST 2-42
JP10, A/B 2-42
JP11, ENCODER INTERFACE 2-42
JP12, CAN termination 2-42
JP2, HDBPTST 2-42
JP4, FLT Bypass 2-42
JP5, PGM SOURCE 2-42
JP6, EDGE/ENCODER 2-42
JP7, EDGE/ENCODER 2-42
JP8, PGM SOURCE 2-42
JP9, ENCODER INTERFACE 2-42
K
KEB
Car oscillates 1-60
Car overshoots 1-60
Contract Speed 1-55
Drive response 1-53
Initial Speed Calibration 1-26
Speed changes felt excessively 1-60
KEB Setup Overview 1-24
L
L24V 2-45
Landing System 1-14, 2-16, 2-32
Landing System ID 2-9
Landing System Learn 1-10, 1-14, 1-52, 2-15
Landing System Type 2-5
Landing System Utilities 1-14, 2-15
Landing System View 2-15
lanterns 1-49
Latch Door Close 2-7
Latch Door Open 2-7
Lead/Acid Batteries 3-2
Learn 1-10
Learn Modes
Hoistway Learn 1-10
Landing System Learn 1-10
Terminal Switch Learn 1-10
Learn modes 1-10
Learn Operation
Repeat if S-Curve adjusted 1-10
Level Distance 2-13
Level Overspeed 2-13
Level Speed 2-13
Leveling Overspeed message 2-72
Leveling speed 1-55
light load antinuisance 2-72
LLI 2-26
Light Load Input 1-50
LLI Antinuisance 2-6
LLI Antinuisance message 2-72
LOAD DISP 2-20
Load Disp 1-50
LOAD HEAVY 2-20
Load Heavy 1-50
Load Hvy 1-50
LOAD LIGHT 2-20
Load Light Input 1-50
load light input active 2-6
LOAD OVER 2-20
Load Over 1-50
LOAD OVER2 2-20
Load Ovr 1-50
Load Ovr2 1-50
load weighers 1-50
Lobby Call Timer 2-8
Lobby Floor 2-5
LOCKS 1-12
Logical position display 1-13
LOP 2-26
LOPM 2-26, 2-46, 2-50
LOT 2-26
LS Config Error message 2-72
LS-EDGE
Access Ovrspd message 2-73
Inspect Ovrspd message 2-73
LS-EDGE Boot Correction message 2-72
LS-EDGE Boot with Error message 2-72
LS-EDGE Count Error message 2-73
LS-EDGE Floor Checksum message 2-73
LS-EDGE installation 1-27–1-35
LS-EDGE Landing System 1-27–1-35
LS-EDGE Learn Active message 2-73
LS-Edge Position Error message 2-73
LS-RAIL installation 1-36–1-42
LS-RAIL Landing System 1-36–1-42
M
M2L Input Mismatch message 2-73
M2L is Low message 2-73
Machine Rm Inspection 1-19
Machine Room Construct message 2-73
Machine Room Enable 1-19
Machine Room Inspection 2-41
Machine Room Inspection message 2-74
Magnetek
Car oscillates 1-60
Car overshoots 1-60
Contract Speed 1-55
Drive response 1-53
Drive response adjustment 1-53
Initial Speed Calibration 1-26
Speed change felt excessively 1-60
MAIN CLOCK 2-26
Main CPI IO’s 2-16