NETGEAR XS708T User Manual

Manage Device Security
325
XS708T, XS712Tv2, and XS716T Smart Managed Pro Switch User Manual
• IPX
• MPLS multicast
• MPLS unicast
• NetBIOS
• Novell
• PPPoE
• Reverse ARP
• User Value
17. In the EtherType User Value field, specify the customized EtherType value that must be
used when you select User Value from the EtherType Key menu.
This value must be compared against the information in an Ethernet frame. The valid range
of values is 0x0600 to 0xFFFF.
18. In the Source MAC field, specify the source MAC address that must be compared against
the information in an Ethernet frame.
The valid format is xx:xx:xx:xx:xx:xx.
19. In the Source MAC Mask field, specify the source MAC address mask that must be
compared against the information in an Ethernet frame.
The valid format is xx:xx:xx:xx:xx:xx.
20. In the VLAN field, specify the VLAN ID that must be compared against the information in an
Ethernet frame.
The valid range of values is 1 to 4095. Either VLAN range or VLAN can be configured.
21. From the Logging menu, select whether to enable or disable logging.
When set to Enable, logging is enabled for this ACL rule (subject to resource availability
on the switch). If the access list trap flag is also enabled, periodic traps are generated,
indicating the number of times the rule was evoked during the report interval. A fixed
five-minute report interval is used for the switch. A trap is not issued if the ACL rule hit
count is zero for the interval. This field is only supported for a deny action.
22. Click the Add button.
The rule is added.
Change the Match Criteria for a MAC Rule
 To change the match criteria for a MAC rule:
1. Connect your computer to the same network as the switch.
You can use a WiFi or wired connection to connect your computer to the network, or
connect directly to a switch that is off-network using an Ethernet cable.
2. Launch a web browser.
3. In the address field of your web browser, enter the IP address of the switch.

NETGEAR XS708T Specifications

General

Switch type	Managed
Switch layer	L2+/L3
Quality of Service (QoS) support	Yes
USB 2.0 ports quantity	1
SFP+ module slots quantity	2
Installed SFP modules quantity	-
Basic switching RJ-45 Ethernet ports type	10G Ethernet (100/1000/10000)
Basic switching RJ-45 Ethernet ports quantity	8
Certification	CE, FCC Cl. A, VCCI Cl. A, Cl. A EN 55022 (CISPR 22), Cl. A C-Tick, EN 55024, CCC
Product color	Black
LED indicators	Activity, Link, Power
Number of fans	1 fan(s)
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3an, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Virtual LAN features	Private VLAN, Protocol-based VLAN
Cable types supported	Cat5e, Cat6, Cat6a, Cat7
Copper ethernet cabling technology	10GBASE-T
Noise level	29.1 dB
Flash memory	256 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276832 h
Jumbo frames	9000
Latency (10 Gbps)	3.012 µs
MAC address table	16000 entries
Packet buffer memory	2 MB
Number of static routes	32
DHCP features	DHCP server, DHCP client
Security algorithms	802.1x RADIUS
Access Control List (ACL) rules	100
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	96 W
Operating altitude	0 - 3000 m
Operating temperature (T-T)	0 - 50 °C
Operating relative humidity (H-H)	0 - 90 %
Cables included	AC

Weight and Dimensions

Depth	204 mm
Width	440 mm
Height	43 mm
Weight	2980 g