EasyManuals Logo

NETGEAR XS708T User Manual

NETGEAR XS708T
442 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #349 background imageLoading...
Page #349 background image
Manage Device Security
349
XS708T, XS712Tv2, and XS716T Smart Managed Pro Switch User Manual
Greater Than. The IPv6 ACL rule matches if the Layer 4 destination port
number is greater than the specified port number.
Not Equal. The IPv6 ACL rule matches only if the Layer 4 destination port
number is not equal to the specified port number or port protocol.
- If you select the Range radio button, the IPv6 ACL rule matches only if the
Layer 4 destination port number is within the specified port range. The starting
port, ending port, and all ports in between are a part of the Layer 4 port range.
The Start Port and End Port fields identify the first and last ports that are part of
the port range. They values can range from 0 to 65535.
You can either enter the port range yourself or select one of the following
protocols from the menu:
The destination IP TCP port protocols are domain, echo, ftp, ftpdata,
www-http, smtp, telnet, pop2, pop3, and bgp.
The destination IP UDP port protocols are domain, echo, snmp, ntp, rip,
time, who, and tftp.
Each of these values translates into its equivalent port number, which is used as
both the start and end of the port range.
Select Other from the menu to enter port numbers. If you select Other from the
menu but leave the fields blank, it means any.
ICMPv6. Select either the Type or Message radio button:
- If you select the Type radio button, note the following:
The Type and Message fields are enabled only if the protocol is ICMPv6. Use
these fields to specify a match condition for ICMPv6 packets.
The IPv6 ACL rule matches the specified ICMPv6 message type. Possible
type numbers are in the range from 0 to 255.
If you specify information in the Message field, the IPv6 ACL rule matches the
specified ICMPv6 message code. Possible values for code can be in the
range from 0 to 255.
If these fields are left empty, it means any.
- If you select the Message radio button, select the type of the ICMPv6 message to
match with the selected IPv6
ACL rule. Specifying a type of message implies that
both the ICMPv6 type and ICMPv6 code are specified.
The ICMPv6 message is
decoded into the corresponding ICMPv6 type and ICMPv6 code within the ICMP
type.
The ICMPv6 message types are destination-unreachable, echo-reply,
echo-request, header, hop-limit, mld-query, mld-reduction, mld-report,
nd-na, nd-ns, next-header, no-admin, no-route, packet-too-big,
port-unreachable, router-solicitation, router-advertisement,
router-renumbering, time-exceeded, and unreachable.

Table of Contents

Other manuals for NETGEAR XS708T

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR XS708T and is the answer not in the manual?

NETGEAR XS708T Specifications

General IconGeneral
Switch typeManaged
Switch layerL2+/L3
Quality of Service (QoS) supportYes
USB 2.0 ports quantity1
SFP+ module slots quantity2
Installed SFP modules quantity-
Basic switching RJ-45 Ethernet ports type10G Ethernet (100/1000/10000)
Basic switching RJ-45 Ethernet ports quantity8
CertificationCE, FCC Cl. A, VCCI Cl. A, Cl. A EN 55022 (CISPR 22), Cl. A C-Tick, EN 55024, CCC
Product colorBlack
LED indicatorsActivity, Link, Power
Number of fans1 fan(s)
Number of VLANs256
Networking standardsIEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3an, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Virtual LAN featuresPrivate VLAN, Protocol-based VLAN
Cable types supportedCat5e, Cat6, Cat6a, Cat7
Copper ethernet cabling technology10GBASE-T
Noise level29.1 dB
Flash memory256 MB
Internal memory512 MB
Processor frequency600 MHz
Mean time between failures (MTBF)276832 h
Jumbo frames9000
Latency (10 Gbps)3.012 µs
MAC address table16000 entries
Packet buffer memory2 MB
Number of static routes32
DHCP featuresDHCP server, DHCP client
Security algorithms802.1x RADIUS
Access Control List (ACL) rules100
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (max)96 W
Operating altitude0 - 3000 m
Operating temperature (T-T)0 - 50 °C
Operating relative humidity (H-H)0 - 90 %
Cables includedAC
Weight and Dimensions IconWeight and Dimensions
Depth204 mm
Width440 mm
Height43 mm
Weight2980 g

Related product manuals