NETGEAR XS708T User Manual

Configure System Information
89
XS708T, XS712Tv2, and XS716T Smart Managed Pro Switch User Manual
The following table describes the non-configurable LLDP-MED Neighbors Information that
displays for the selected interface.
Field Description
LLDP-MED Interface Selection
Remote ID Specifies the remote client identifier assigned to the remote system.
Capability Information
This section of the page specifies the supported and enabled capabilities that are received in MED TLV on
this port.
Supported Capabilities Specifies supported capabilities that are received in MED TLV on this port.
Enabled Capabilities Specifies enabled capabilities that are received in MED TLV on this port.
Device Class Specifies device class as advertised by the device remotely connected to the
port.
Network Policies Information
This section of the page specifies if network policy TLV is received in the LLDP frames on this port.
Media Application Type Specifies the application type: unknown, voicesignaling, guestvoice,
guestvoicesignalling, softphonevoice, videoconferencing, streamingvideo, or
videosignaling.
Information for each application type includes the VLAN ID, priority, DSCP,
tagged bit status and unknown bit status. A port can receive information
about one or many of such application types. The application type is
displayed only if a network policy TLV is received on a port.
VLAN ID Specifies the VLAN ID associated with a particular policy type.
Priority Specifies the priority associated with a particular policy type.
DSCP Specifies the DSCP associated with a particular policy type.
Unknown Bit Status Specifies the unknown bit associated with a particular policy type.
Tagged Bit Status Specifies the tagged bit associated with a particular policy type.
Inventory Information
This section of the page specifies if inventory TLV is received in LLDP frames on this port.
Hardware Revision Specifies the hardware version of the remote device.
Firmware Revision Specifies the firmware version of the remote device.
Software Revision Specifies software version of the remote device.
Serial Number Specifies the serial number of the remote device.
Manufacturer Name Specifies the manufacturer’s name of the remote device.
Model Name Specifies the model name of the remote device.
Asset ID Specifies the asset ID of the remote device.

NETGEAR XS708T Specifications

General

Switch type	Managed
Switch layer	L2+/L3
Quality of Service (QoS) support	Yes
USB 2.0 ports quantity	1
SFP+ module slots quantity	2
Installed SFP modules quantity	-
Basic switching RJ-45 Ethernet ports type	10G Ethernet (100/1000/10000)
Basic switching RJ-45 Ethernet ports quantity	8
Certification	CE, FCC Cl. A, VCCI Cl. A, Cl. A EN 55022 (CISPR 22), Cl. A C-Tick, EN 55024, CCC
Product color	Black
LED indicators	Activity, Link, Power
Number of fans	1 fan(s)
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3an, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Virtual LAN features	Private VLAN, Protocol-based VLAN
Cable types supported	Cat5e, Cat6, Cat6a, Cat7
Copper ethernet cabling technology	10GBASE-T
Noise level	29.1 dB
Flash memory	256 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276832 h
Jumbo frames	9000
Latency (10 Gbps)	3.012 µs
MAC address table	16000 entries
Packet buffer memory	2 MB
Number of static routes	32
DHCP features	DHCP server, DHCP client
Security algorithms	802.1x RADIUS
Access Control List (ACL) rules	100
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	96 W
Operating altitude	0 - 3000 m
Operating temperature (T-T)	0 - 50 °C
Operating relative humidity (H-H)	0 - 90 %
Cables included	AC

Weight and Dimensions

Depth	204 mm
Width	440 mm
Height	43 mm
Weight	2980 g