Ridder VitaLite-E - Page 110

110 pages

Save Page as PDF

To Previous Page

Main Page

Table of Contents3
Introduction to this Manual6
Introduction6
Aims6
Target Groups6
Symbols and Annotations6
Documentation Overview7
Product Information8
Schematic Representation of the Unit8
Basic Configuration9
Description of I/O Modules9
Replacing I/O Modules10
Removing I/O Modules11
Intended Use12
Other Product Characteristics12
Type Plate13
Quality Control13
Components, Stickers and Names14
Certificates and Declarations16
Original Equipment Manufacturers (OEM) Information16
Packaging, Storage and Shipment17
Recycling and Disposal17
Safety Precautions and Requirements19
General Safety Requirements19
Personal Protective Equipment19
UV-C Radiation20
Chemicals21
Emergency Stop21
Installation Procedure22
Installation Requirements22
Dealer/Installer Requirements22
Water Installation Requirements24
Electrical Installation Requirements24
Requirements for Installing Water Tank Sensors24
Installation Checklist25
Connecting Water Components (Water Installation)27
Pre-Blending Control (Optional)28
Filters28
Connecting Electrical Components29
Connecting Acid Dosing Components29
Ph Calibration31
Connecting EC Sensors (if Present)31
EC Calibration31
Installing Quartz Tubes and Lamps32
Installing Quartz Tubes32
Quartz Tube Breakages35
Pressurizing the Unit36
Installing UV-C Lamps37
Other Installation Work38
Display Board of the Control Panel38
Connecting Synopta40
Commissioning41
Control Panel41
Reading out and Setting Variables43
Alarms43
Commissioning44
Log in at Dealer Level44
Check Settings44
Set Start Conditions44
Testing the Unit44
Manually Start Disinfection44
Manually Start Cleaning Quartz Tubes46
Manually Start Filter Flushing47
Quality Control48
Sampling Procedure for CFU Testing48
Operation50
Power Switch50
System Pump and Dosing Pump50
Disinfection51
Warming up UV Lamps52
Disinfection Active53
Stopping Disinfection and Post-Flushing53
Filter Flushing54
Cleaning Quartz Tubes55
Dosing and Circulating Acid55
Post-Flushing after Cleaning Quartz Tubes56
Maintenance and Quality Control57
Maintenance57
Weekly Maintenance57
Monthly Maintenance57
Yearly Maintenance58
Appendix A: Control Overview59
General Settings59
System Settings60
System Configuration61
System Activation61
Identification62
Protected Settings62
Communication65
Console Settings65
IO Bus Settings65
Synopta Settings65
Network Settings66
Modbus Settings66
EC Calibration66
Ph Calibration66
I/O66
Modules66
Control Outputs67
Backup Settings67
Unit67
Control Mode67
Safeguards68
Unit Characteristics69
Drain Group Settings73
Warming up UV Lamps73
Start Conditions74
Period76
Control76
Drain Groups / Safeguards77
Drain Groups / Drain Group Characteristics80
Drain Groups / Control Characteristics80
Cleaning Quartz Tubes Settings82
Cleaning Quartz Tubes / Control83
Cleaning Quartz Tubes / Safeguards85
Control Characteristics86
Filter Flushing Settings86
Filter Flushing / Control86
Filter Flushing / Safeguards88
Filter Flushing / Control Characteristics88
Water Tank Settings88
Drain Tanks89
Disinfected Tanks90
UV Lamps91
Appendix B: Notifications92
Appendix C: Wiring List103
Output / Ph Module, Module ID: 1, Inputs & 4-20Ma Output103
Output / Ph Module, Module ID: 1, Outputs104
Output / Input Module, Module ID: 2, Outputs105
Output / Input Module, Module ID: 2, Inputs106
Output / Input Module 5Th - 8Th Drain Group, Module ID: 3, Outputs107
Output / Input Module 5Th - 8Th Drain Group, Module ID: 3, Inputs108
EC Pre-Blending Module ID109

Ridder VitaLite-E - Page 110

Table of Contents

Related product manuals